Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136).

HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the engine switch is turned off.

·

The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A137607E12
0.105,0.035 3.393,0.224 3.288,0.188 10 Reference (System Diagram of Bank 1 Sensor 2): 2.894,1.277 3.574,1.458 0.680,0.181 10 EFI NO. 2 0.992,1.299 2.014,1.457 1.022,0.159 10 EFI MAIN NO.1 1.938,2.405 2.960,2.564 1.022,0.159 10 EFI MAIN NO.1 1.02,3.33 1.500,3.512 0.480,0.181 10 Ground 3.393,0.367 4.889,0.548 1.496,0.181 10 Heated Oxygen Sensor 3.438,0.976 3.663,1.158 0.226,0.181 10 +B 4.587,0.976 4.967,1.158 0.380,0.181 10 HT1B 3.444,1.547 3.702,1.729 0.258,0.181 10 E2 4.6,1.547 5.025,1.729 0.424,0.181 10 OX1B 5.217,1.547 5.641,1.729 0.424,0.181 10 OX1B 5.217,2.149 5.641,2.331 0.424,0.181 10 EX1B 3.893,0.801 4.329,0.982 0.436,0.181 10 Heater 3.879,1.404 4.338,1.585 0.459,0.181 10 Sensor 5.883,0.325 6.208,0.506 0.326,0.181 10 ECM 5.21,0.969 5.590,1.151 0.380,0.181 10 HT1B 5.21,2.693 5.613,2.874 0.403,0.181 10 MREL 0.485,1.002 0.977,1.363 0.492,0.360 10 from Battery


DTC No. DTC Detection Condition Trouble Area
P0037
P0057
The heated oxygen sensor heater (bank 1, 2 sensor 2) current is below 0.3 A (1 trip detection logic).
·

Open in heated oxygen sensor heater (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

EFI NO. 2 fuse

·

ECM


P0038
P0058
The heated oxygen sensor (bank 1, 2 sensor 2) current is higher than 2 A (1 trip detection logic).
·

Short in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

EFI NO. 2 fuse

·

ECM


P102D
P105D
The heated oxygen sensor heater (bank 1, 2 sensor 2) current is higher than a specified value while the heater is not operating (1 trip detection logic). ECM


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions. If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
U169302E01
2.667,0.594 1.917,1.229 false 2.781,2.823 2.021,3.458 false 0.125,0.042 0.323,0.24 0.198,0.198 10 false *a 0.125,0.313 0.344,0.51 0.219,0.198 10 false *c 0.125,2.292 0.323,2.49 0.198,0.198 10 false *b 2.74,0.438 2.958,0.625 0.219,0.188 10 false +B 2.833,2.698 3.052,2.885 0.219,0.188 10 false +B 0.396,1.094 0.688,1.25 0.292,0.156 10 false C27 0.365,1.542 0.75,1.698 0.385,0.156 10 false C145 0.427,3.521 0.719,3.677 0.292,0.156 10 false C28 0.885,3.5 1.135,3.688 0.25,0.188 10 false *A 0.844,1.521 1.094,1.708 0.25,0.188 10 false *B

a.

Disconnect the heated oxygen sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Automatic Transmission
Tester Connection Switch Condition Specified Condition
C27-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C145-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V

for Manual Transmission
Tester Connection Switch Condition Specified Condition
C27-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C28-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for Manual Transmission
*B for Automatic Transmission
*a Front view of wire harness connector
(to Heated Oxygen Sensor Bank 1)
*b Front view of wire harness connector
(to Heated Oxygen Sensor Bank 2)
*c Front view of wire harness connector
(to Heated Oxygen Sensor Bank 2)


c.

Reconnect the heated oxygen sensor connector.



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) - C37-18 (HT1B) Always Below 1 Ω
C145-1 (HT2B) - C37-13 (HT2B) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) - C37-12 (HT1B) Always Below 1 Ω
C28-1 (HT2B) - C37-13 (HT2B) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) or C37-18 (HT1B) - Body ground Always 10 kΩ or higher
C145-1 (HT2B) or C37-13 (HT2B) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) or C37-12 (HT1B) - Body ground Always 10 kΩ or higher
C28-1 (HT2B) or C37-13 (HT2B) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the heated oxygen sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C27-2 (+B) - 1W-10 Always Below 1 Ω
C145-2 (+B) - 1W-10 Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C27-2 (+B) - 1W-10 Always Below 1 Ω
C28-2 (+B) - 1W-10 Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C27-2 (+B) or 1W-10 - Body ground Always 10 kΩ or higher
C145-2 (+B) or 1W-10 - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C27-2 (+B) or 1W-10 - Body ground Always 10 kΩ or higher
C28-2 (+B) or 1W-10 - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the heated oxygen sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR