Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A412055E01
0.719,2.333 4.698,2.531 3.979,0.198 10 false Combination Meter Assembly 0.719,2.135 1.292,2.313 0.573,0.177 10 false G304 2.01,1.583 2.583,1.76 0.573,0.177 10 false CANL 2,0.885 2.573,1.063 0.573,0.177 10 false CANH 2.531,1.396 3.104,1.573 0.573,0.177 10 false 39 2.531,0.688 3.104,0.865 0.573,0.177 10 false 40 4.5,1.385 5.073,1.563 0.573,0.177 10 false 36 4.5,0.698 5.073,0.875 0.573,0.177 10 false 35 5.458,2.167 6.031,2.344 0.573,0.177 10 false G58 5.448,2.344 6.021,2.521 0.573,0.177 10 false ECM 4.813,1.583 5.385,1.76 0.573,0.177 10 false CANL 4.813,0.875 5.385,1.052 0.573,0.177 10 false CANH 1.021,3.417 4.688,3.615 3.667,0.198 10 false : CAN Communication Line

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check the illumination condition of the MIL.


Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → engine is started A
Other than above - B



A

B

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

4.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY