The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.
When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.
For the circuit diagram of the ECM power source circuit.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>ECM Power Source Circuit
VC Power Source Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
| *a | Component with harness connected
(to ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G185-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| G185-3 (+B2) - Body ground | Ignition switch ON | 11 to 14 V |
| G185-4 (+B3) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is not as specified, since current is not flowing to the +B, +B2 and +B3 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the camshaft position sensor connector.
A
B
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the manifold absolute pressure sensor connector.
A
B
Disconnect the mass air flow meter sub-assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the mass air flow meter sub-assembly connector.
A
B
Disconnect the nozzle vane position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the nozzle vane position sensor connector.
A
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL
B
Disconnect the electric EGR control valve assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the electric EGR control valve assembly connector.
A
B
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the accelerator pedal position sensor connector.
A
B
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the fuel pressure sensor connector.
A
B
Disconnect the diesel throttle body assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the diesel throttle body assembly connector.
A
B
Disconnect the crankshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
Reconnect the crankshaft position sensor connector.
A
B
Disconnect the clutch stroke sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is notpossible | B |
Reconnect the clutch stroke sensor connector.
A
B
Disconnect the diesel throttle body assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the electric EGR control valve assembly connector.
Disconnect the differential pressure sensor connector.
Disconnect the nozzle vane position sensor connector.
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the camshaft position sensor connector.
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C151-29 (VCVL) - Body ground and other terminals | Always | 10 kΩ or higher |
| G185-29 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| G185-30 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-28 (VCM) - Body ground and other terminals | Always | 10 kΩ or higher |
| C149-28 (VCPM) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-31 (VCEG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-32 (VCPX) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-30 (VNVC) - Body ground and other terminals | Always | 10 kΩ or higher |
| C150-25 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C152-17 (VCG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C152-20 (VCNE) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the diesel throttle body assembly connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the electric EGR control valve assembly connector.
Reconnect the differential pressure sensor connector.
Reconnect the nozzle vane position sensor connector.
Reconnect the mass air flow meter sub-assembly connector.
Reconnect the camshaft position sensor connector.
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG