Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

·

The cruise control main switch outputs the cruise control power supply switch signal and each operation switch signal to the ECM.

·

The ECM performs cruise control according to the signal from the cruise control main switch.


WIRING DIAGRAM

C387810E01
0.875,3.25 4.083,3.448 3.208,0.198 10 false Cruise Control Switch 4.333,3.094 5.26,3.469 0.927,0.375 10 false Spiral Cable Sub-assembly 6.354,2.625 6.969,2.823 0.615,0.198 10 false ECCS*4 6.333,0.521 6.948,0.719 0.615,0.198 10 false CCS 6.427,3.865 7.042,4.063 0.615,0.198 10 false ECCS 3.104,1.573 3.719,1.771 0.615,0.198 10 false CCS 3.104,2.479 3.719,2.677 0.615,0.198 10 false ECC 0.51,2.031 1.427,2.229 0.917,0.198 10 false CANCEL 1.302,2.031 1.917,2.229 0.615,0.198 10 false -SET 2.073,2.042 2.688,2.24 0.615,0.198 10 false +RES 2.844,2.052 3.76,2.25 0.917,0.198 10 false ON-OFF 4.677,1.573 5.292,1.771 0.615,0.198 10 false CCS 4.677,2.479 5.292,2.677 0.615,0.198 10 false ECC 0.208,3.771 2.354,3.969 2.146,0.198 10 false *1: for 1GR-FE 0.219,4.094 2.365,4.292 2.146,0.198 10 false *2: for 1KD-FTV 0.229,4.438 2.375,4.635 2.146,0.198 10 false *3: for 1GD-FTV 0.24,4.792 2.385,4.99 2.146,0.198 10 false *4: for 2TR-FE 0.25,5.146 2.5,5.396 2.25,0.25 10 false *5: Cruise Control Switch Wire 3.677,2.865 3.99,3.063 0.313,0.198 10 false *5 4.646,0.75 4.958,0.948 0.313,0.198 10 false *1 5.083,0.75 5.396,0.948 0.313,0.198 10 false *2 5.563,0.75 5.875,0.948 0.313,0.198 10 false *3 5.99,0.76 6.302,0.958 0.313,0.198 10 false *4 5.885,0.521 6.5,0.719 0.615,0.198 10 false G181 5.448,0.521 6.063,0.719 0.615,0.198 10 false G185 4.583,0.521 5.198,0.719 0.615,0.198 10 false G56 5.875,2.594 6.49,2.792 0.615,0.198 10 false G181 5.083,1.688 5.698,1.885 0.615,0.198 10 false G208 5.083,2.594 5.698,2.792 0.615,0.198 10 false G208 4.188,1.688 4.5,1.885 0.313,0.198 10 false z7 4.188,2.583 4.5,2.781 0.313,0.198 10 false z7 4.656,0.281 4.969,0.479 0.313,0.198 10 false 1 5.073,0.292 5.385,0.49 0.313,0.198 10 false 14 5.521,0.292 5.833,0.49 0.313,0.198 10 false 26 5.958,0.292 6.271,0.49 0.313,0.198 10 false 22 5.031,0.521 5.646,0.719 0.615,0.198 10 false G57 5.958,2.375 6.271,2.573 0.313,0.198 10 false 21 5.208,2.365 5.521,2.563 0.313,0.198 10 false 2 4.219,1.469 4.531,1.667 0.313,0.198 10 false 3 4.219,2.365 4.531,2.563 0.313,0.198 10 false 4 3.5,1.573 3.813,1.771 0.313,0.198 10 false 3 3.5,2.469 3.813,2.667 0.313,0.198 10 false 1 5.198,1.458 5.51,1.656 0.313,0.198 10 false 1 5.99,2.823 6.302,3.021 0.313,0.198 10 false *4 5.51,3.271 5.823,3.469 0.313,0.198 10 false *3 5.51,3.083 5.823,3.281 0.313,0.198 10 false *2 5.5,2.896 5.813,3.094 0.313,0.198 10 false *1 0.875,3.104 1.188,3.302 0.313,0.198 10 false A

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Check the Data List for proper functioning of the cruise control switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise 1 > Data List

Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control switch is pushed, ON or OFF changes
Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF Each time cruise control switch is pushed, ON or OFF changes

OK:

When the cruise control switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.

Disconnect the z7 spiral cable sub-assembly connector.


b.

Disconnect the A cruise control switch wire connector.


c.
E178683C37
0.292,0.729 0.729,1.042 0.438,0.313 0.24,2.385 0.677,2.698 0.438,0.313 1.656,1.542 1.281,1.094 true 0.656,1.542 1.073,1.125 true 0.583,3.073 1,2.656 true 1.813,3.094 1.438,2.646 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 0.24,1.969 0.552,2.167 0.313,0.198 10 false *b 0.417,2.458 0.573,2.656 0.156,0.198 10 false A 0.438,0.823 0.75,1.021 0.313,0.198 10 false z7 1.573,1.583 2.031,1.781 0.458,0.198 10 false ECC 0.49,1.552 0.948,1.75 0.458,0.198 10 false CCS 0.417,3.104 0.875,3.302 0.458,0.198 10 false ECC 1.698,3.125 2.156,3.323 0.458,0.198 10 false CCS
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z7-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z7-4 (ECC) - A-1 (ECC) Always Below 1 Ω
z7-3 (CCS) or A-3 (CCS) - Body ground Always 10 kΩ or higher
z7-4 (ECC) or A-1 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the G56*1, G57*2, G185*3 or G181*4 ECM connector.

·

*1: for 1GR-FE

·

*2: for 1KD-FTV

·

*3: for 1GD-FTV

·

*4: for 2TR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 1GR-FE):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G56-1 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G56-1 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 1KD-FTV):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G57-14 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G56-36 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 1GD-FTV):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G185-26 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G185-26 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 2TR-FE):
Tester Connection Condition Specified Condition
G208-1 (CCS) - G181-22 (CCS) Always Below 1 Ω
G208-2 (ECC) - G181-21 (ECCS) Always Below 1 Ω
G208-1 (CCS) or G181-22 (CCS) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for 1GR-FE, 1KD-FTV, 1GD-FTV) A
OK (for 2TR-FE) B
NG C



A

B

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the C153 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR