Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1361  Short in ABS Motor Fail Safe Relay Circuit  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

The motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the pump motor.

If the voltage supplied to the motor relay (BM) is below the DTC detection threshold due to low voltage from the battery or generator, these DTCs may be stored.

DTC Code DTC Detection Condition Trouble Area
C1361 Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the motor fail-safe relay is off.
·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)


C146C Either condition is met:
1.

All conditions are met for 0.12 seconds or more.

-

The IG1 terminal voltage is between 9.5 and 17.2 V.

-

During initial check and ABS, BA, TRC or VSC is operating.

-

The relay contact is open when the relay is on.


2.

Both conditions are met for 0.12 seconds.

-

The IG1 terminal voltage is below 9.5 V.

-

The relay contact remains open when the relay is on.



·

ABS NO. 1 fuse

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)


C146D When the motor relay is off, the motor relay remains closed for 4 seconds or more.
·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C215406E22
1.917,1.563 2.698,1.719 0.781,0.156 10 false ABS NO. 1 3.552,1.313 3.948,1.479 0.396,0.167 10 false 24 3.552,3.375 3.969,3.531 0.417,0.156 10 false 13 3.813,1.5 4.354,1.698 0.542,0.198 10 false BM 3.813,3.563 4.448,3.802 0.635,0.24 10 false GND2 4.885,0.604 6.01,0.76 1.125,0.156 10 false Skid Control ECU 5.083,1.313 5.875,1.5 0.792,0.188 10 false Motor Relay 4.792,3.375 6.167,3.563 1.375,0.188 10 false Motor Fail-safe Relay 5.24,4.729 6.042,4.917 0.802,0.188 10 false Pump Motor 3.833,5.135 4.333,5.292 0.5,0.156 10 false A6 3.833,5.292 6.073,5.448 2.24,0.156 10 false Brake Actuator Assembly 0.458,2.771 1.281,3.031 0.823,0.26 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1241 is output together with DTC C1361, C146C and/or C146D, inspect and repair the trouble areas indicated by DTC C1241 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay Motor relay Relay ON / OFF The operating sound of the motor can be heard.


f.

Check the operating sound of the motor relay when operating it with the GTS.

Result
Result Proceed to
Operating sound is not heard A
Operating sound is heard B



A

2.CHECK TERMINAL VOLTAGE (BM)

B

4.RECONFIRM DTC
2.CHECK TERMINAL VOLTAGE (BM)
a.

Turn the ignition switch off.


b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.
U148916E01
2.49,1.26 2.323,1.917 2.323,1.917 2.177,1.917 false 0.052,0.021 0.344,0.219 0.292,0.198 10 false *a 1.865,1.833 2.177,2 0.313,0.167 10 false BM 0.281,0.938 0.563,1.115 0.281,0.177 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-24 (BM) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-13 (GND2) - Body ground Always Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
HINT:

This code is stored when a problem is identified in the skid control ECU (brake actuator assembly).

The motor relay is in the brake actuator assembly.

Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).


a.

Turn the ignition switch off.


b.

Reconnect the A6 skid control ECU (brake actuator assembly) connector.



d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC not output A
DTC output B

HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness. The DTCs were probably output due to a bad connection of the connector terminal.





A

B