Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0332058 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The forward recognition camera communicates with the driving support ECU assembly and millimeter wave radar sensor assembly via CAN communication. If there is a communication error with the driving support ECU assembly or millimeter wave radar sensor assembly, the forward recognition camera stores DTC U0235 or U1104.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor 2 seconds after the ignition switch is turned ON, a communication error between the millimeter wave radar sensor assembly and the forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera


U1104 Lost Communication with Driving Support ECU 2 seconds after the ignition switch is turned ON, a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Driving support ECU assembly

·

Forward recognition camera



WIRING DIAGRAM

C383555E01
1.135,2.542 3.583,2.74 2.448,0.198 10 false Forward Recognition Camera 1.125,2.396 1.583,2.594 0.458,0.198 10 false W22 1.583,1.979 2.042,2.177 0.458,0.198 10 false GND 1.333,1.875 1.646,2.073 0.313,0.198 10 false 10 2.115,1.5 2.573,1.698 0.458,0.198 10 false IGB 1.99,1.74 2.604,1.938 0.615,0.198 10 false CANL 2.51,1.365 2.667,1.563 0.156,0.198 10 false 7 2.5,1.594 2.813,1.792 0.313,0.198 10 false 12 1.99,2.01 2.604,2.208 0.615,0.198 10 false CANH 2.51,1.865 2.667,2.063 0.156,0.198 10 false 6 2.125,3.25 2.583,3.448 0.458,0.198 10 false IGB 2.5,3.115 2.656,3.313 0.156,0.198 10 false 8 2,3.594 2.615,3.792 0.615,0.198 10 false CA1P 2.5,3.427 2.656,3.625 0.156,0.198 10 false 5 2.01,4.083 2.625,4.281 0.615,0.198 10 false CA1N 2.5,3.906 2.656,4.104 0.156,0.198 10 false 6 1.583,3.896 2.198,4.094 0.615,0.198 10 false SGND 1.385,3.781 1.542,3.979 0.156,0.198 10 false 1 0.844,4.552 1.302,4.75 0.458,0.198 10 false A100 0.833,4.698 3.74,4.896 2.906,0.198 10 false Millimeter Wave Radar Sensor Assembly 4.938,4.479 5.552,4.677 0.615,0.198 10 false G224 4.958,4.646 6.917,4.885 1.958,0.24 10 false Driving Support ECU Assembly 5.979,3.969 6.438,4.167 0.458,0.198 10 false GND 6.396,3.854 6.708,4.052 0.313,0.198 10 false 28 5.5,3.594 6.115,3.792 0.615,0.198 10 false CA1P 5.51,4.083 6.125,4.281 0.615,0.198 10 false CA1N 5.271,3.406 5.427,3.604 0.156,0.198 10 false 8 5.271,3.917 5.427,4.115 0.156,0.198 10 false 9 5.521,0.458 5.677,0.656 0.156,0.198 10 false B 5.281,0.333 5.438,0.531 0.156,0.198 10 false 7 3.927,0.615 4.875,0.906 0.948,0.292 10 false ECU-IG NO. 1 1.104,5.281 2.917,5.438 1.813,0.156 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

HINT:

When pre-crash safety system DTC U1002 is output, check that the local bus is functioning normally by performing the diagnosis procedure for U1002.



Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

3.CHECK FOR SHORT IN CAN BUS LINE

B

3.CHECK FOR SHORT IN CAN BUS LINE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
E374719C04
0.552,1.042 0.958,1.323 0.406,0.281 2.146,1.104 2.5,0.823 true 2.156,1.417 2.51,1.604 true 0.625,1.094 1.083,1.292 0.458,0.198 10 false W22 2.552,0.75 3.167,0.948 0.615,0.198 10 false CANH 2.563,1.531 3.177,1.729 0.615,0.198 10 false CANL 0.125,0.094 0.458,0.333 0.333,0.24 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the W22 forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-6 (CANH) - W22-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


HINT:

If the result is not as specified, a malfunction in a CAN communication line is suspected.



e.

Reconnect the W22 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE)

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

Result:
Result Proceed to
DTC U0235 and U1104 are output A
Only DTC U1104 is output B
Only DTC U0235 is output C



A

5.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)

B

7.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)

C

10.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
5.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)
a.
E374720C02
1.563,0.198 2.01,0.448 0.448,0.25 1.229,0.979 0.896,0.385 true 2.771,1.781 2.479,1.25 true 0.104,0.073 0.344,0.281 0.24,0.208 10 false *a 1.635,0.24 2.25,0.438 0.615,0.198 10 false G224 0.76,0.292 0.917,0.49 0.156,0.198 10 false B 2.833,1.729 3.292,1.927 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G224-7 (B) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-28 (GND) - Body ground Always Below 1 Ω



f.

Reconnect the G224 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
E374721C02
1.5,0.156 1.896,0.406 0.396,0.25 0.75,1.823 1.417,1.052 true 2.51,1.865 1.938,1.229 true 0.104,0.083 0.406,0.323 0.302,0.24 10 false *a 1.542,0.198 2,0.396 0.458,0.198 10 false A100 0.354,1.823 0.969,2.021 0.615,0.198 10 false SGND 2.563,1.833 3.208,2.083 0.646,0.25 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A100 millimeter wave radar sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A100-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-1 (SGND) - Body ground Always Below 1 Ω



f.

Reconnect the A100 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)
a.
E374720C02
1.563,0.198 2.01,0.448 0.448,0.25 1.229,0.979 0.896,0.385 true 2.771,1.781 2.479,1.25 true 0.104,0.073 0.344,0.281 0.24,0.208 10 false *a 1.635,0.24 2.25,0.438 0.615,0.198 10 false G224 0.76,0.292 0.917,0.49 0.156,0.198 10 false B 2.833,1.729 3.292,1.927 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G224-7 (B) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-28 (GND) - Body ground Always Below 1 Ω



f.

Reconnect the G224 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
9.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA

10.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
E374721C02
1.5,0.156 1.896,0.406 0.396,0.25 0.75,1.823 1.417,1.052 true 2.51,1.865 1.938,1.229 true 0.104,0.083 0.406,0.323 0.302,0.24 10 false *a 1.542,0.198 2,0.396 0.458,0.198 10 false A100 0.354,1.823 0.969,2.021 0.615,0.198 10 false SGND 2.563,1.833 3.208,2.083 0.646,0.25 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A100 millimeter wave radar sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A100-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-1 (SGND) - Body ground Always Below 1 Ω



f.

Reconnect the A100 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
12.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA