The skid control ECU (brake actuator assembly*1 or master cylinder solenoid*2) receives vehicle stability signals from the yaw rate sensor. If the skid control ECU (brake actuator assembly*1 or master cylinder solenoid*2) detects a yaw rate sensor zero point malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA6 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA6 | Yaw Rate Sensor Zero Point Malfunction | 2 seconds after the ignition switch is turned ON, a signal from the skid control ECU (brake actuator assembly*1 or master cylinder solenoid*2) indicating a malfunction in the yaw rate sensor zero point is detected by the forward recognition camera for 5 seconds or more. | ·
Vehicle stability control system ·
Skid control ECU (brake actuator assembly*1 or master cylinder solenoid*2) ·
Forward recognition camera |
*1: for 2TR-FE
*2: except 2TR-FE
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Check for DTCs.
for 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR
except 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR
If DTC C1AA6 is stored, the VSC system may be malfunctioning. Check for DTCs related to the VSC system first.
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
for 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DIAGNOSIS SYSTEM
except 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DIAGNOSTIC TROUBLE CODE CHART
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA6 is not output | A |
| DTC C1AA6 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform Forward Recognition Camera Learning.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA6 is not output | A |
| DTC C1AA6 is output (for 2TR-FE) | B |
| DTC C1AA6 is output (except 2TR-FE) | C |
A
B
C
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REMOVAL