The glass hatch opener system enables the back door glass to be opened when the glass hatch opener switch is pressed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*
*: w/ Entry and Start System
Check vehicle type.
| Result | Proceed to |
|---|---|
| except 5L-E | A |
| for 5L-E | B |
A
B
Use the Data List to check if the back door courtesy light switch is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Courtesy SW | Back door courtesy switch signal / ON or OFF | ON: Back door open
OFF: Back door closed |
- |
On the tester screen, item changes between ON and OFF according to above chart.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (except 5L-E)>Back Door Courtesy Switch Circuit
Confirm that the vehicle is equipped with the entry and start system.
| Result | Proceed to |
|---|---|
| w/ Entry and Start System | A |
| w/o Entry and Start System | B |
A
B
When the back door entry lock switch is operated, check that the glass hatch opens.
The back door entry lock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use the Data List to check if the glass hatch opener switch is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Glass Hatch Opener Switch | Glass hatch opener switch signal / ON or OFF | ON: Glass hatch opener switch operated
OFF: Glass hatch opener switch not operated |
- |
Glass hatch opener switch operates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Glass Hatch Open | Operate Glass Hatch | ON/OFF | - |
The glass hatch is opened.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back window lock assembly.
Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW LOCK>REMOVAL
Inspect the back window lock assembly.
Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X4 back window lock assembly connector.
Disconnect the 2Q*1 or 2P*2 driver side junction block assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-3 (+) - 2Q-7 | Always | Below 1 Ω |
| X4-4 (-) - Body ground | Always | Below 1 Ω |
| X4-3 (+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-3 (+) - 2P-7 | Always | Below 1 Ω |
| X4-4 (-) - Body ground | Always | Below 1 Ω |
| X4-3 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for LHD *2: for RHD |
||
| 2Q-7 - Battery negative (-) terminal*1
2P-7 - Battery negative (-) terminal*2 |
Battery not connected to 2M-7 and A-6 (GHRY) | Below 1 V |
| Battery positive (+) → 2M-7
Battery negative (-) → A-6 (GHRY) |
11 to 14 V | |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for LHD *2: for RHD |
||
| 2Q-7 - Battery negative (-) terminal*1
2P-7 - Battery negative (-) terminal*2 |
Battery not connected to 2M-8 and A-6 (GHRY) | Below 1 V |
| Battery positive (+) → 2M-8
Battery negative (-) → A-6 (GHRY) |
11 to 14 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the glass hatch opener switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SWITCH>REMOVAL
Inspect the glass hatch opener switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X3 glass hatch opener switch assembly connector.
Disconnect the G216 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X3-2 - G216-28 (GOSW) | Always | Below 1 Ω |
| X3-1 - Body ground | Always | Below 1 Ω |
| X3-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use the Data List to check if the back door courtesy light switch is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Courtesy SW | Back door courtesy switch signal / ON or OFF | ON: Back door open
OFF: Back door closed |
- |
On the tester screen, item changes between ON and OFF according to above chart.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (for 5L-E)>Back Door Courtesy Switch Circuit
Use the Data List to check if the glass hatch opener switch is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Glass Hatch Opener Switch | Glass hatch opener switch signal / ON or OFF | ON: Glass hatch opener switch operated
OFF: Glass hatch opener switch not operated |
- |
| Result | Proceed to |
|---|---|
| Glass hatch opener switch does not operate | A |
| Glass hatch opener switch operates | B |
A
B
Remove the glass hatch opener switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SWITCH>REMOVAL
Inspect the glass hatch opener switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X3 glass hatch opener switch assembly connector.
Disconnect the G63 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X3-2 - G63-17 (GOSW) | Always | Below 1 Ω |
| X3-1 - Body ground | Always | Below 1 Ω |
| X3-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>WINDOW / GLASS>GLASS HATCH OPENER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Glass Hatch Open | Operate Glass Hatch | ON/OFF | - |
The glass hatch is opened.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back window lock assembly.
Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW LOCK>REMOVAL
Inspect the back window lock assembly.
Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X4 back window lock assembly connector.
Disconnect the 2I*1 or 2H*2 driver side junction block assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-3 (+) - 2I-9 | Always | Below 1 Ω |
| X4-4 (-) - Body ground | Always | Below 1 Ω |
| X4-3 (+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-3 (+) - 2H-9 | Always | Below 1 Ω |
| X4-4 (-) - Body ground | Always | Below 1 Ω |
| X4-3 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for LHD *2: for RHD |
||
| 2I-9 - Battery negative (-) terminal*1
2H-9 - Battery negative (-) terminal*2 |
Battery not connected to 2K-1 and A-6 (GHRY) | Below 1 V |
| Battery positive (+) → 2K-1
Battery negative (-) → A-6 (GHRY) |
11 to 14 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG