Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › from 2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1782  Low Battery Positive Voltage  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
C1782 The voltage at terminal IG or B is 10 V or less or 16 V or higher for 0.5 seconds.
·

Battery

·

Charging system

·

AIR SUS fuse

·

AIR SUS NO. 2 fuse

·

AVS fuse

·

Harness or connector

·

Suspension control ECU



WIRING DIAGRAM

C218589E01
0.372,0.615 1.204,0.873 0.832,0.258 10 from Battery 3.384,0.83 4.383,1.088 0.998,0.258 10 AIR SUS NO. 2 2.135,0.83 2.820,1.025 0.685,0.195 10 AIR SUS 3.006,1.381 3.368,1.585 0.362,0.205 10 AVS 5.911,0.634 6.220,0.891 0.309,0.258 10 B 5.911,1.203 6.127,1.461 0.216,0.258 10 IG 5.911,1.811 6.284,2.068 0.373,0.258 10 GND 5.911,2.397 6.333,2.655 0.422,0.258 10 GND 0.226,1.194 1.188,1.563 0.961,0.369 10 from IG Circuit 5.582,1.581 5.700,1.764 0.118,0.184 10 5 5.582,0.973 5.768,1.157 0.186,0.184 10 1 5.538,2.166 5.713,2.350 0.175,0.184 10 10 5.582,0.406 5.700,0.589 0.118,0.184 10 3 5.377,3.167 6.978,3.351 1.601,0.184 10 Suspension Control ECU 5.488,0.626 5.801,0.819 0.313,0.193 10 A49 5.497,1.207 5.811,1.400 0.313,0.193 10 A49 5.497,1.794 5.811,1.987 0.313,0.193 10 A49 5.496,2.388 5.818,2.572 0.323,0.184 10 R19

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (IG/+B POWER SOURCE VOLTAGE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Source Voltage Actual ECU power supply voltage / Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11 to 14 V -
+B Power Source Voltage Actual battery supply voltage / Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11 to 14 V -

Standard voltage:

11 to 14 V


Result
Result Proceed to
NG A
OK (When troubleshooting according to problem symptoms table) B
OK (When troubleshooting according to DTC chart) C



A

2.CHECK TERMINAL VOLTAGE (IG, B)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.CHECK TERMINAL VOLTAGE (IG, B)
a.

Disconnect the A49 suspension control ECU connector.


b.
U148537E02
1.042,1.167 0.396,1.292 0.396,1.292 0.396,1.406 true 1.656,1.167 2.938,1.292 2.938,1.292 2.938,1.406 true 0.135,0.104 0.333,0.271 0.198,0.167 10 false *a 0.344,1.406 0.521,1.573 0.177,0.167 10 false IG 2.896,1.406 3.073,1.573 0.177,0.167 10 false B 1.563,0.292 1.885,0.448 0.323,0.156 10 false A49

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-3 (B) - Body ground Always 11 to 14 V
A49-1 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BODY GROUND)
a.

Disconnect the A49 and R19 suspension control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R19-10 (GND) - Body ground Always Below 1Ω
A49-5 (GND) - Body ground Always Below 1Ω




OK

4.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR DTC

b.

Check for DTCs (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

REPLACE SUSPENSION CONTROL ECU