Wear protective gloves. Sharp areas on the parts may injure your hands.
Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).
The fold seat control ECU is replaced with a new one.
Initialization (initial position reset) of the fold seat control ECU is performed.
Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).
The fold seat control ECU is exchanged with one from another vehicle.
The seatback frame and seat leg are inspected.
The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
The seatback frame or seat leg is replaced.
The cable is disconnected from the battery while the seatback or seat cushion is operating.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
73949
1.REMOVE CAP
Remove the 2 caps.
71693
2.REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH
Remove the 2 screws.
Detach the 3 claws and remove the rear seat cushion lower hinge cover LH.
71693
3.REMOVE REAR SEAT CUSHION LOWER HINGE COVER RH
Remove the 2 screws.
| *1 | Guide |
Detach the 2 claws and guide and remove the rear seat cushion lower hinge cover RH.
73590
4.REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
89715
5.REMOVE FOLD SEAT CONTROL ECU
71827B
6.REMOVE REAR SEAT NO. 1 CUSHION MOULDING
Using a clip remover, remove the 2 clips.
Detach the 2 claws and 4 guides to remove the rear seat No. 1 cushion moulding.
| *1 | Guide |
7.REMOVE SEAT CUSHION COVER WITH PAD
Open the 2 fasteners.
| *1 | Fastener |
Remove the 2 clips and open the under part of the seat cushion cover.
Detach the 2 hooks and remove the seat cushion cover with pad.
| *1 | Hook |
79032
8.REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
Detach the fastener.
| *1 | Fastener |
Remove the 2 hog rings and No. 3 seat cushion cover sub-assembly LH.
71647F
9.REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH
Cut off the 5 tack pins and remove the rear seat cushion inner edge protector LH from the seat cushion pad.
| *1 | Tack Pin |
71827B
10.REMOVE REAR SEAT NO. 2 CUSHION MOULDING
Remove the 2 screws.
Detach the 2 claws and remove the rear seat No. 2 cushion moulding.
79384A
11.REMOVE REAR SEAT NO. 3 LEG COVER LH
Detach the 2 claws and remove the rear seat No. 3 leg cover LH.
71694E
12.REMOVE REAR SEAT CUSHION INNER HINGE COVER LH
Remove the screw and clip.
| *1 | Guide |
Detach the guide and remove the rear seat cushion inner hinge cover LH.
71694E
13.REMOVE REAR SEAT CUSHION INNER HINGE COVER RH
Remove the screw and clip.
| *1 | Guide |
Detach the guide and remove the rear seat cushion inner hinge cover RH.
72152
14.REMOVE LOWER SEAT TRACK RAIL LH (w/ Seatback Rail)
Remove the 2 bolts and lower seat track rail LH.
66310F
15.REMOVE ROPE HOOK ASSEMBLY (w/ Seatback Hook)
Using a screwdriver, detach the 2 claws and open the cover.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
Remove the bolt and rope hook assembly.
71702C
16.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH
w/ Seatback Rail:
Detach the 7 clips and remove the rear seatback board sub-assembly LH.
w/ Seatback Hook:
Detach the 7 clips and remove the rear seatback board sub-assembly LH.
72635B
17.REMOVE REAR SEATBACK LOCK HOOK
Remove the rear seatback lock hook.
71865
18.REMOVE REAR SEAT NO. 1 COVER BEZEL
Remove the 2 screws.
| *1 | Guide |
Detach the guide and remove the rear seat No. 1 cover bezel.
19.REMOVE SEATBACK COVER WITH PAD
Detach the 6 hooks.
| *1 | Hook |
| *2 | Hog Ring |
Remove the 2 hog rings
Detach the 8 clips and remove the seatback cover with pad.
79034
20.REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
Remove the 7 hog rings and No. 3 seatback cover sub-assembly LH.
71587C
21.REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR
Cut off the 5 tack pins and remove the rear No. 2 seatback edge protector from the seatback pad.
| *1 | Tack Pin |
79962
22.REMOVE NO. 2 SEATBACK COVER
Detach the 2 claws and remove the No. 2 seatback cover.
71970A
23.REMOVE REAR SEAT HEADREST COVER
Remove the 2 screws.
| *1 | Guide |
Detach the 2 claws and guide to remove the rear seat headrest cover.
71987A
24.REMOVE REAR SEAT HEADREST CABLE
Detach the 2 clamps.
| *1 | Cable End |
| *2 | Clamp |
Twist the 2 cable ends in the direction indicated by the arrow and remove the rear seat headrest cable.
71970
25.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the 3 nuts and rear seat headrest assembly.
71587C
26.REMOVE REAR SEATBACK EDGE PROTECTOR
Detach the 4 claws and remove the 2 rear seatback edge protectors.
71834C
27.REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH
Detach the 4 claws and remove the rear No. 3 seat inner reclining cover LH.
71834C
28.REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH
Remove the screw.
| *1 | Guide |
Detach the guide and 2 claws to remove the rear No. 3 seat outer reclining cover LH.
79202
29.REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
Remove the bolt and disconnect the wire harness.
Using a screwdriver, release the lock lever as shown in the illustration.
Retract the seat cushion frame.
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and No. 2 seat cushion frame sub-assembly LH.
79384
30.REMOVE REAR SEAT LEG COVER LH
Remove the clip.
| *1 | Hook |
Detach the 3 hooks and 5 clips to remove the rear seat leg cover LH.
72906
31.REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH
Remove the 3 clips.
| *1 | Guide |
Detach the 2 claws and 4 guides to remove the 3rd seat link sub-assembly LH.
71844C
32.REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH
Detach the 5 claws and remove the rear No. 2 seat inner reclining cover LH.
71844A
33.REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH
Remove the screw.
| *1 | Guide |
Detach the guide and 2 claws to remove the rear No. 2 seat outer reclining cover LH.
72690A
34.REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH
Detach the 2 clamps.
| *1 | Clamp |
| *2 | Cable End |
Twist the cable end in the direction indicated by the arrow and remove the rear seat lock release strap assembly LH.
72690A
35.REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)
Cut off the 2 cable ties and detach the 3 clamps.
| *1 | Cable Tie |
| *2 | Clamp |
| *3 | Cable End |
Twist the cable end in the direction indicated by the arrow and remove the rear seat lock release strap assembly RH.
72695C
36.REMOVE REAR SEAT LOCK CONTROL CABLE LH
Detach the 2 clamps.
| *1 | Cable End |
| *2 | Clamp |
Twist the 2 cable ends in the direction indicated by the arrow and remove the rear seat lock control cable LH.
72695B
37.REMOVE REAR SEAT LOCK CONTROL CABLE RH (for RH Side)
Cut off the 2 cable ties and detach the 3 clamps.
| *1 | Cable Tie |
| *2 | Clamp |
| *3 | Cable End |
Twist the 2 cable ends in the direction indicated by the arrow and remove the rear seat lock control cable RH.
79304A
38.REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and No. 3 seatback frame sub-assembly LH.
82196
39.REMOVE REAR NO. 2 SEAT WIRE LH
Disconnect the connector.
Detach the wire harness clamps and remove the rear No. 2 seat wire LH.
79040
40.REMOVE NO. 3 SEAT LEG ASSEMBLY LH
Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg assembly LH.
79020B
41.REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side)
Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg assembly.