Wear protective gloves. Sharp areas on the parts may injure your hands.
Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).
The fold seat control ECU is replaced with a new one.
Initialization (initial position reset) of the fold seat control ECU is performed.
Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).
The fold seat control ECU is exchanged with one from another vehicle.
The seatback frame and seat leg are inspected.
The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
The seatback frame or seat leg is replaced.
The cable is disconnected from the battery while the seatback or seat cushion is operating.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
79040
1.INSTALL NO. 3 SEAT LEG ASSEMBLY LH
Install the seat cushion under carpet LH to the No. 3 seat leg assembly LH with 4 new clips.
79020B
2.INSTALL NO. 2 SEAT LEG ASSEMBLY (for RH Side)
Install the seat cushion under carpet RH to the No. 2 seat leg assembly with 4 new clips.
82196
3.INSTALL REAR NO. 2 SEAT WIRE LH
Attach the wire harness clamps to install the No. 2 seat wire LH.
Connect the connector.
79304A
4.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, install the No. 3 seatback frame sub-assembly LH with the 4 "TORX" bolts.
72695C
5.INSTALL REAR SEAT LOCK CONTROL CABLE LH
Twist the 2 cable ends in the direction indicated by the arrow to connect them.
| *1 | Cable End |
| *2 | Clamp |
Attach the 2 clamps to install the rear seat lock control cable LH.
Install at the middle level of the cable clamp (triple level) side.
72695B
6.INSTALL REAR SEAT LOCK CONTROL CABLE RH (for RH Side)
Twist the 2 cable ends in the direction indicated by the arrow to connect them.
| *1 | Cable Tie |
| *2 | Clamp |
| *3 | Cable End |
Attach the 3 clamps to install the rear seat lock control cable RH.
Install at the middle level of the cable clamp (triple level) side.
Install 2 new cable ties.
72690A
7.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Cable End |
| *2 | Clamp |
Attach the 2 clamps to install the rear seat lock release strap assembly LH.
72690A
8.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Cable Tie |
| *2 | Clamp |
| *3 | Cable End |
Attach the 3 clamps to install the rear seat lock release strap assembly RH.
Install the 2 new cable ties.
71844A
9.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH
Attach the 2 claws and guide to install the rear No. 2 seat outer reclining cover LH.
Install the screw.
71844C
10.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH
Attach the 5 claws to install the rear No. 2 seat inner reclining cover LH.
72906
11.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH
Attach the 4 guides and 2 claws to install the 3rd seat link sub-assembly LH.
Install 3 new clips.
79384
12.INSTALL REAR SEAT LEG COVER LH
Attach the 5 clips and 3 hooks to install the rear seat leg cover LH.
Install a new clip.
79202
13.INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
Using a T40 "TORX" socket wrench, install the No. 2 seat cushion frame sub-assembly LH with the 4 "TORX" bolts.
Pull out the No. 2 seat cushion frame sub-assembly LH.
Connect the wire harness with the bolt.
71834C
14.INSTALL REAR NO. 3 SEAT OUTER RECLINING COVER LH
Attach the 2 claws and guide to install the rear No. 3 seat outer reclining cover LH.
Install the screw.
71834C
15.INSTALL REAR NO. 3 SEAT INNER RECLINING COVER LH
Attach the 4 claws to install the rear No. 3 seat inner reclining cover LH.
71587C
16.INSTALL REAR SEATBACK EDGE PROTECTOR
Attach the 4 claws to install the 2 rear seatback edge protectors.
71970
17.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the rear seat headrest assembly with the 3 nuts.
71987A
18.INSTALL REAR SEAT HEADREST CABLE
Twist the 2 cable ends in the direction indicated by the arrow to install them.
| *1 | Cable End |
| *2 | Clamp |
Attach the 2 clamps to install the rear seat headrest cable.
71970A
19.INSTALL REAR SEAT HEADREST COVER
Attach the 2 claws and guide to install the rear seat headrest cover.
Install the 2 screws.
79962
20.INSTALL NO. 2 SEATBACK COVER
Attach the 2 claws to install the No. 2 seatback cover.
71587C
21.INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR
Install the rear No. 2 seatback edge protector to the seatback pad with 5 new tack pins.
79034
22.INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the No. 3 seatback cover sub-assembly LH to the seatback pad with 7 new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
23.INSTALL SEATBACK COVER WITH PAD
Attach the 8 clips.
Using hog ring pliers, install the 2 new hog rings.
Attach the 6 hooks to install the seatback cover with pad.
71865
24.INSTALL REAR SEAT NO. 1 COVER BEZEL
Pass the strap through the bezel hole.
Attach the guide to install the rear seat No. 1 cover bezel.
Install the 2 screws.
72635B
25.INSTALL REAR SEATBACK LOCK HOOK
Install the rear seatback lock hook.
71702C
26.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
w/ Seatback Rail:
Attach the 7 clips in the order as shown in the illustration to install the rear seatback board sub-assembly LH.
w/ Seatback Hook:
Attach the 7 clips in the order as shown in the illustration to install the rear seatback board sub-assembly LH.
66310F
27.INSTALL ROPE HOOK ASSEMBLY (w/ Seatback Hook)
Install the rope hook assembly with the bolt.
Attach the 2 claws to close the cover.
72152
28.INSTALL LOWER SEAT TRACK RAIL LH (w/ Seatback Rail)
Install the lower seat track rail LH with the 2 bolts.
71694E
29.INSTALL REAR SEAT CUSHION INNER HINGE COVER RH
Attach the guide to install the rear seat cushion inner hinge cover RH.
Install the screw and a new clip.
71694E
30.INSTALL REAR SEAT CUSHION INNER HINGE COVER LH
Attach the guide to install the rear seat cushion inner hinge cover LH.
Install the screw and a new clip.
79384A
31.INSTALL REAR NO. 3 SEAT LEG COVER LH
Attach the 2 claws to install the rear No. 3 seat leg cover LH.
71827B
32.INSTALL REAR SEAT NO. 2 CUSHION MOULDING
Attach the 2 claws to install the rear seat No. 2 cushion moulding.
Install the 2 screws.
71647F
33.INSTALL REAR SEAT CUSHION INNER EDGE PROTECTOR LH
Install the rear seat cushion inner edge protector LH to the seat cushion pad with 5 new tack pins.
79032
34.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the No. 3 seat cushion cover sub-assembly to the seat cushion pad with 2 new hog rings.
| *1 | Fastener |
| *2 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the fastener.
35.INSTALL SEAT CUSHION COVER WITH PAD
Attach the 2 hooks to install the seat cushion cover with pad.
Close the under part of the seat cushion coveri and install 2 new clips.
Close the 2 fasteners.
71827B
36.INSTALL REAR SEAT NO. 1 CUSHION MOULDING
Attach the 4 guides and 2 claws to install the rear seat No. 1 cushion moulding.
Install 2 new clips.
89715
37.INSTALL FOLD SEAT CONTROL ECU
73590
38.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
71693
39.INSTALL REAR SEAT CUSHION LOWER HINGE COVER RH
Attach the 2 claws to install the rear seat cushion lower hinge cover RH.
Install the 2 screws.
71693
40.INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH
Attach the guide and 2 claws to install the rear seat cushion lower hinge cover LH.
Install the 2 screws.
73949
41.INSTALL CAP
Install the 2 caps.