Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P2002  Diesel Particulate Filter Efficiency Below Threshold Bank 1  P2458  Diesel Particulate Filter Regeneration Duration  P2463  Diesel Particulate Filter Restriction - Soot Accumulation  


DESCRIPTION

DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A413706E01
0.938,0.188 0.75,0.188 0.75,0.188 1.135,0.771 true 3.323,1.177 3.135,1.177 3.135,1.177 2.823,1.771 true 3.385,2 3.198,2 3.198,2 2.969,2.406 true 3.781,2.542 3.594,2.542 3.594,2.542 3.458,2.75 true 3.344,3.146 3.156,3.146 3.156,3.146 2.865,3.417 true 3.635,7.417 3.375,7.865 3.375,7.865 4.74,7.625 true 1.667,8.271 1.406,7.906 true 6.177,8.135 5.708,8.031 true 6.385,7.729 6.448,7.396 true 5.729,4.802 5.938,4.802 5.938,4.802 6.365,5.219 true 1.531,3.813 2.469,2.844 true 1.771,2.75 2.479,2.469 true 1.49,2.094 2.5,2.208 true 1.063,0.104 5.646,0.302 4.583,0.198 10 false Exhaust Fuel Addition Injector 0.021,0.771 0.542,1.24 0.521,0.469 10 false Exhaust Gas 3.396,1.094 5.865,1.479 2.469,0.385 10 false Exhaust Gas Temperature Sensor 3.417,1.927 6.031,2.281 2.615,0.354 10 false No. 2 Exhaust Gas Temperature Sensor 3.917,2.469 6.531,2.823 2.615,0.354 10 false Differential Pressure Sensor 3.417,3.052 6.031,3.406 2.615,0.354 10 false No. 3 Exhaust Gas Temperature Sensor 3.458,6.229 6.073,6.583 2.615,0.354 10 false Monolithic Construction: 0.51,6.24 3.125,6.594 2.615,0.354 10 false DPF (Diesel Particulate Filter): 2.531,6.74 5.146,7.094 2.615,0.354 10 false PM, HC, CO 2.146,7.854 3.365,8.313 1.219,0.458 10 false Alternating Blocked Passages 1.708,8.292 4.323,8.646 2.615,0.354 10 false DPF (Diesel Particulate Filter) Catalyst 5.458,8.427 7.156,8.792 1.698,0.365 10 false Magnified View 6.229,8.083 6.542,8.281 0.313,0.198 10 false PM 6.323,7.771 7.156,8.021 0.833,0.25 10 false Gas Flow 4.802,6.5 5.635,6.75 0.833,0.25 10 false CO2, H2O 5.375,6.229 7.156,6.469 1.781,0.24 10 false Wall-Flow Type: 4.104,4.719 6.469,5.073 2.365,0.354 10 false Particulate Matter Sensor 3.615,5.729 6.229,6.083 2.615,0.354 10 false SCR 1 4.958,5.719 6.104,6.063 1.146,0.344 10 false SCR 2 0.708,3.823 3.073,4.177 2.365,0.354 10 false DPF Catalyst 0.063,2.656 1.771,3.052 1.708,0.396 10 false Exhaust Manifold Converter Sub-assembly 0.615,2.031 2.979,2.385 2.365,0.354 10 false DOC Catalyst 3.76,7.875 5.458,8.24 1.698,0.365 10 false Cross Section 6.219,1.219 6.677,1.417 0.458,0.198 10 false ECM

P0420
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes.
(2 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P2002
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
·

After warming the engine, drive the vehicle at approximately 50 km/h for approximately 15 minutes after performing PM forced regeneration.

(DTC detection condition (a))

·

Increase the engine speed to 4000 rpm with no load and maintain it for 10 seconds or more

(DTC detection condition (b))


Either condition is met:

(a) PM Sensor Output Current exceeds 12 μA

(2 trip detection logic)

(b) When driving, the catalyst differential pressure is continuously below the threshold for 7 seconds or more.

(2 trip detection logic)


·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly

·

Particulate matter sensor


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P2458
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse.
(1 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P2463
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic)
·

Exhaust Manifold Converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



HINT:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).


Related Data List
DTC No. Data List
P0420
P2002
P2458
P2463
·

Exhaust Fuel Addition FB

·

Catalyst Differential Press

·

DPF Differential Pressure

·

PM Sensor Output Current



MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the exhaust manifold converter sub-assembly.

Abnormal DOC catalyst temperature increase:

The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL.

A208470E10
3.229,1.875 3.323,2.031 3.323,2.031 3.49,2.031 false 5.229,1.875 5.302,1.625 5.302,1.625 5.417,1.625 false 5.135,1.458 5.083,1.281 5.083,1.281 4.958,1.281 false 5.313,1.427 5.396,0.875 5.396,0.875 5.531,0.875 false 0.083,0.083 2.052,0.417 1.969,0.333 10 false Catalyst Activation Malfunction: (DPF No Activate) 0.896,0.938 2.76,1.302 1.865,0.365 10 false PM Forced Regeneration (Activation of Fuel Addition) 1.115,1.781 2.781,1.958 1.667,0.177 10 false Exhaust Gas Temperature 3.521,1.958 4.938,2.198 1.417,0.24 10 false About 300°C (572°F) 5.458,1.563 6.104,1.729 0.646,0.167 10 false Abnormal 4.49,1.208 4.969,1.375 0.479,0.167 10 false Normal 3.323,0.813 3.635,1 0.313,0.188 10 false Off 5.135,0.385 5.375,0.542 0.24,0.156 10 false On 5.563,0.802 7.063,1.146 1.5,0.344 10 false More than About 500°C (932°F) 4.24,2.438 4.594,2.594 0.354,0.156 10 false Time


Reduced catalytic converter efficiency:

Reduced catalytic converter efficiency is a reduction in performance (crack) detected by the PM monitor used by particulate matter sensor behind the DPF and the DPF differential pressure monitor used by the differential pressure sensor.

-

PM Monitor:

The ECU uses the particulate matter sensor to monitor the amount of PM behind the DPF after driving.

If the DPF is damaged (cracked) and the PM behind the DPF increases, the particulate matter sensor reacts and outputs a value.

When the output value of the particulate matter sensor exceeds the threshold value, the ECU judges that the DPF is damaged (cracked) and illuminates the MIL.

-

Differential Pressure Monitor:

The ECU uses the differential pressure sensor and monitors the pressure difference in front and behind the DPF.

If the DPF is damaged (cracked) and the pressure loss in the DPF is decreased, the differential pressure sensor value decreases.

When the output value of the differential pressure sensor falls below the threshold value, the ECU judges that the DPF is damaged (cracked) and illuminates the MIL.



Catalytic converter regeneration duration:

When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.


Excessive PM accumulation:

The ECM monitors the PM Accumulation Ratio and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an injector assembly, the ECM needs registration.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

·

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

If DTC P2458 or P2463 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-MAIN NO. 1 fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.



f.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

·

When the Catalyst Differential Press value is more than 0.27, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P2002, P2458 AND P2463)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P2002, P2458 AND P2463)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2002 is output A
DTC P244B is output at the same time as P2463* B
DTC P0420, P2458 or P2463 is output C
Other relevant DTCs are output D


HINT:
·

*: When DTC P244B is output at the same time as P2463, perform troubleshooting for P244B.

·

When DTC P1603, P1604 or P1608 is output in addition to P0420, perform troubleshooting for P1603, P1604 or P1608 first.





A

3.CHECK FREEZE FRAME DATA (PM SENSOR OUTPUT CURRENT)

B

GO TO DTC P244B

C

12.CHECK FOR BLACK SMOKE

D

11.GO TO DTC CHART
3.CHECK FREEZE FRAME DATA (PM SENSOR OUTPUT CURRENT)
a.

Read the value of "PM Sensor Output Current" in the freeze frame data recorded in Procedure 1.

Result:
Result Proceed to
PM Sensor Output Current is 12 μA or more
(Detected by the PM monitoring function used by the particulate matter sensor)
A
PM Sensor Output Current is less than 12 μA.
(Detected by the pressure difference monitoring function used by the differential pressure sensor.)
B


HINT:

If the PM Sensor Output Current is 12 μA or more, DTC P2002 is output according to detection by the PM monitor function used by the particulate matter sensor.




A

9.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY AND PARTICULATE MATTER SENSOR

B

4.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
4.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


HINT:

Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.


A360341C01
4.396,2.135 4.99,1.563 4.99,1.563 5.083,1.563 true 2.198,1.417 2.292,1.417 2.292,1.417 2.698,2.01 true 3.688,1.031 4.521,0.302 4.521,0.302 4.615,0.302 true 2.917,0.323 3.01,0.323 3.01,0.323 3.417,0.917 true 2.74,0.25 3.052,0.406 0.313,0.156 10 false *1 4.656,0.229 4.969,0.385 0.313,0.156 10 false *2 2.042,1.354 2.354,1.51 0.313,0.156 10 false *3 5.125,1.49 5.438,1.646 0.313,0.156 10 false *4
*1 Air Hose (Downstream) *2 Air Hose (Upstream)
*3 No. 2 Vacuum Pipe *4 No. 1 Vacuum Pipe


a.
A362182C03
0.615,0.958 1.667,1.302 true 0.625,0.958 1.323,0.844 false 0.458,0.885 0.771,1.042 0.313,0.156 10 false *1
*1 Air Hose


Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

NG

10.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
5.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


d.

Check that the differential pressure is as specified below.

OK:

Approximately 0 kPa



Result:
Proceed to
OK
NG



OK

6.CONNECT UPSTREAM AIR HOSE

NG

7.REPLACE DIFFERENTIAL PRESSURE SENSOR
6.CONNECT UPSTREAM AIR HOSE
a.
A362181C01
1.75,1.198 2.073,0.99 2.073,0.99 2.188,0.99 true 2.25,0.927 2.563,1.125 0.313,0.198 10 false *1
*1 Air Hose (Upstream)


Connect the upstream air hose to the differential pressure sensor.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


e.

Start the engine.


f.

Engine is running at 4000 rpm with no load for 10 seconds or more.


g.

Check that the differential pressure is as specified below.

Result:
DPF Differential Pressure Proceed to
1.5 kPa or higher A
Below 1.5 kPa B




B

7.REPLACE DIFFERENTIAL PRESSURE SENSOR

A

8.CONNECT DOWNSTREAM AIR HOSE
7.REPLACE DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

8.CONNECT DOWNSTREAM AIR HOSE
8.CONNECT DOWNSTREAM AIR HOSE
a.

Connect the downstream air hose to the differential pressure sensor.

A360341C04
2.917,0.323 3.01,0.323 3.01,0.323 3.417,0.917 true 2.74,0.25 3.052,0.406 0.313,0.156 10 false *1
*1 Air Hose (Downstream) - -



b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


e.

Start the engine.


f.

Engine is running at 4000 rpm with no load for 10 seconds or more.


g.

Check that the differential pressure is as specified below.

Result:
DPF Differential Pressure Proceed to
-1.5 to 1.5 kPa A
Higher than 1.5 kPa B




A

9.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY AND PARTICULATE MATTER SENSOR

B

12.CHECK FOR BLACK SMOKE
9.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY AND PARTICULATE MATTER SENSOR
a.

It has been determined that the exhaust manifold converter sub-assembly and particulate matter sensor needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly and particulate matter sensor.

HINT:
·

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.

·

If a vehicle is brought into the workshop and it is determined that the exhaust manifold converter sub-assembly is to be replaced due to DTC P2002, replace the particulate matter sensor at the same time.

If soot is stuck on the particulate matter sensor due to cracking in the DPF catalyst, the particulate matter sensor may react and perform incorrect judgment even after repairing the DPF catalyst back to its normal condition.




Result:
Proceed to
NEXT



NEXT

14.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
10.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
a.

Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.


Result:
Proceed to
NEXT



NEXT

5.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
11.GO TO DTC CHART

NEXT

12.CHECK FOR BLACK SMOKE
12.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

13.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

OK

14.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
13.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

14.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
14.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Remove the EFI MAIN NO. 1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI MAIN NO. 1 fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Turn the engine switch on (IG).


c.

Turn the engine switch off and wait for 30 seconds or more.


d.

Turn the engine switch on (IG) and wait for 10 seconds or more.


e.

Connect the GTS to the DLC3.


f.

Turn the GTS on.


g.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


h.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




i.

Enter the following menus: Powertrain / Engine / Active Test / Activate the DPF Rejuvenate (PM) / Data List / Diesel Exhaust / Exhaust Temperature B1S2.


j.

Perform the Active Test.

CAUTION:

Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.


HINT:

When PM Accumulation Ratio is too low, Activate the DPF Rejuvenate (PM) cannot be performed. Therefore, rev the engine with no load at 3400 rpm for 5 to 10 minutes to increase PM Accumulation Ratio to 12% or more.



k.

Check for temperature increases and abnormal white smoke during PM forced regeneration.

HINT:
·

PM forced regeneration takes 15 to 40 minutes to finish.

·

The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio" and the vehicle operating conditions.

·

If the value of "Catalyst Differential Press" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.

·

Perform PM forced regeneration control until the display on the multi-information display turns off.

·

If actions such as depressing the accelerator pedal, clutch pedal or operating the DPF switch, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.

·

PM forced regeneration control is not complete until the display on the multi-information display turns off.



Result:
Result Proceed to
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and no white smoke is generated A
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and abnormal white smoke is generated*1 B
Other than above*2 C


HINT:
·

*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst.

·

*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.

·

*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.





A

15.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

17.CHECK FUEL INJECTION SYSTEM
15.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

It has been determined that the exhaust fuel addition injector assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly.


Result:
Proceed to
NEXT



NEXT

17.CHECK FUEL INJECTION SYSTEM
16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.



Result:
Proceed to
NEXT



NEXT

17.CHECK FUEL INJECTION SYSTEM
17.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

18.CHECK INTAKE/EXHAUST SYSTEM
18.CHECK INTAKE/EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

19.CHECK AFTER TREATMENT CONTROL SYSTEM
19.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

20.REPAIR OR REPLACE MALFUNCTIONING PARTS
20.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P0420, P2002, P2458 and P2463.


a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL

NOTICE:

Perform the initialization procedure for "DPF catalyst record clear" and "DPF Deterioration Record Clear"

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION



b.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


c.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.


d.

Check for DTCs output in step 1.

HINT:

If DTC 2002 is output, check if it was detected by the PM monitor or differential pressure monitor using the freeze frame data in step 2.


Result:
Result Proceed to
DTC P2002 is output (detected by PM monitor) A
DTC P2002 is output (detected by differential pressure monitor) B
DTC other than DTC P2002 output C




A

21.CLEAN EXHAUST PIPE

B

22.CLEAN EXHAUST PIPE

C

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CLEAN EXHAUST PIPE
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Connect the GTS to the DLC3.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

HINT:
·

If a vehicle is brought into the workshop due to DTC P2002, soot may be stuck in the SCR exhaust pipe. Therefore, clear the soot out of the SCR exhaust pipe by racing the engine.

·

P2002 may be output again as a result of the particulate matter sensor reacting to the soot stuck in the SCR exhaust pipe being blown out. If P2002 is output again, clear it after racing the engine.




Result:
Proceed to
NEXT



NEXT

END

22.CLEAN EXHAUST PIPE
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Connect the GTS to the DLC3.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

HINT:
·

If a vehicle is brought into the workshop due to DTC P2002, soot may be stuck in the SCR exhaust pipe. Therefore, clear the soot out of the SCR exhaust pipe by racing the engine.

·

P2002 may be output again as a result of the particulate matter sensor reacting to the soot stuck in the SCR exhaust pipe being blown out. If P2002 is output again, clear it after racing the engine.




Result:
Proceed to
NEXT



NEXT

23.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
23.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


d.

Start the engine.


e.

Engine is running at 4000 rpm with no load for 10 seconds or more.


f.

Confirmation that the differential pressure is higher than 1.5 kPa.


Result:
Proceed to
NEXT



NEXT

END

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
NEXT



NEXT

END