Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL INJECTOR › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260590 FUEL INJECTOR A

1GD-FTV FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work .(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (Click here General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 25800 3.REMOVE EGR COOLER ASSEMBLY

Hide 89463C 5.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

a.
A425655

Remove the 2 bolts, detach the connector, and then disconnect the No. 1 nitrogen oxides sensor from the cylinder head cover sub-assembly.


Hide 7.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A339108

Disconnect the pressure discharge valve connector from the common rail assembly.


b.

Remove the bolt and wiring harness clamp bracket from the cylinder head cover sub-assembly.


Hide 8.REMOVE HARNESS BRACKET

a.
A339109

Remove the bolt and harness bracket.


Hide 23760 9.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A339110

Slide the clamp and disconnect the No. 5 fuel hose from the nozzle leakage pipe assembly.


b.

Remove the 4 union bolts and 4 gaskets.


c.

Remove the bolt and nozzle leakage pipe assembly.


Hide 10.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

NOTICE:

After removing the No. 1 and No. 2 injection pipe sub-assemblies, cover the common rail assembly with electrical tape to prevent dirt or foreign objects from entering the pipe inlet. Also, protect the injector inlets with electrical tape or plastic bags.


a.
A352787E02
1.594,1.531 1.385,0.854 1.385,0.854 1.146,0.854 true 0.813,0.771 1.167,0.979 0.354,0.208 10 true SST

Using SST, loosen the No. 1 and No. 2 injection pipe sub-assemblies and 8 union nuts of the fuel injector assembly side and common rail assembly side.

SST
09245-11010  


b.
A339111

Remove the 2 No. 1 injection pipe sub-assemblies and 2 No. 2 injection pipe sub-assemblies.

NOTICE:

When removing the No. 1 injection pipe subassembly and No. 2 injection pipe sub-assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.



Hide 23670 11.REMOVE INJECTOR ASSEMBLY

a.
A344925

Remove the 4 nozzle holder clamp bolts, 4 washers and 4 nozzle holder clamps.


b.

Remove the 4 fuel injector assemblies and 4 injection nozzle seats from the cylinder head sub-assembly.

NOTICE:

When removing the injector assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.



c.

Remove the O-ring from each injector assembly.


Hide 23682 12.REMOVE NOZZLE HOLDER GASKET

a.
A344926

Remove the 4 nozzle holder gaskets from the cylinder head cover sub-assembly.