Refer to DTC P200C.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P200C
For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION
If DTC P20CD is present, refer to the DTC table for Diesel Particulate Filter System.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 3 second | With the exhaust fuel addition injector assembly off, the FIVO output is high for 3 seconds.
(1 trip detection logic) |
·
Open or short in exhaust fuel addition injector assembly circuit ·
Exhaust fuel addition injector assembly ·
ECM |
DTC P200C, P200E, P20CF and/or P2428 will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.
In order to detect abnormality in the fuel addition injector assembly, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVO) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector assembly via a drive circuit inside the ECM. The FIVO signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVO signal, the ECM judges that the current has been applied to the exhaust fuel addition injector assembly.
This DTC will be set if the ECM judges that the number of signals of the FIV and FIVO are inconsistent.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the exhaust fuel addition injector assembly
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>INSPECTION
OK
NG
| *a | Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly) |
Disconnect the exhaust fuel addition injector assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C180-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
Reconnect the exhaust fuel addition injector assembly connector.
OK
NG
Disconnect the exhaust fuel addition injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C180-1 - G184-6 (FIV) | Always | Below 1 Ω |
| C180-1 or G184-6 (FIV) - Body ground and other terminal | Always | 10 kΩ or higher |
Reconnect the exhaust fuel addition injector assembly connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NEXT
Replace the exhaust fuel addition injector assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL
NEXT
If the voltage at the exhaust fuel addition injector assembly connector is not 11 to 14 V, repair or replace the harness and connector between the exhaust fuel addition injector assembly and No. 1 integration relay.
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR
Turn the engine switch off for 30 seconds or more.
The exhaust gas temperature increases to 250°C (482°F) or higher after driving the vehicle for 20 minutes.
Turn the engine switch on (IG) for 3 seconds.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT