Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P24AF  Particulate Matter Sensor Circuit Range/Performance  P24B0  Particulate Matter Sensor Circuit Low  P24B1  Particulate Matter Sensor Circuit High  P24B3  Particulate Matter Sensor Heater Control Circuit/Open  P24C6  Particulate Matter Sensor Temperature Circuit  P24D0  Particulate Matter Sensor Supply Voltage Circuit Low  


DESCRIPTION

The particulate matter sensor is installed in the center exhaust pipe assembly to detect the PM value.

P24AF
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) and wait for 10 seconds or more. Particulate matter sensor out of range for 3 seconds or more
(2 trip detection logic)
·

Particulate matter sensor



P24B0
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) and wait for 10 seconds or more. Open or short in particulate matter sensor circuit for 3 seconds or more
(2 trip detection logic)
·

Particulate matter sensor



P24B1
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) and wait for 10 seconds or more. Open or short in particulate matter sensor circuit for 3 seconds or more
(2 trip detection logic)
·

Particulate matter sensor



P24B3
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) and wait for 10 seconds or more. Malfunction in particulate matter sensor circuit for 3 seconds or more
(2 trip detection logic)
·

Particulate matter sensor



P24C6
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) and wait for 10 seconds or more. Malfunction in particulate matter sensor temperature sensor for 3 seconds or more
(2 trip detection logic)
·

Particulate matter sensor



P24D0
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) and wait for 10 seconds or more. Low power supply to particulate matter sensor circuit for 3 seconds or more
(2 trip detection logic)
·

Particulate matter sensor

·

NOx PM relay

·

Harness or connector



DTC No. Data List
P24AF
P24B0
P24B1
P24B3
P24C6
P24D0
·

PM Sensor Output Current

·

Status of PM Sensor IDE Circuit

·

Status of PM Sensor IDE (+ Side)

·

Status of PM Sensor Temperature

·

Status of PM Sensor IDE (- Side)

·

Status of PM Sensor Heater ON Malfunction

·

Status of PM Sensor Heater OFF Malfunction



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.



Result:
Result Proceed to
DTC P24D0 is output A
DTC P24AF,P24B0,P24B1,P24B3,P24C6 is output B
DTC P24AF or P24B0,P24B1,P24B3,P24C6,P24D0 and other DTCs are output* C


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.



A

2.INSPECT NOX PM RELAY

B

7.REPLACE PARTICULATE MATTER SENSOR

C

2.INSPECT NOX PM RELAY

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR

NG

6.REPLACE NOX PM RELAY
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect the Particulate matter sensor assembly connector.


b.

Remove the NOx PM relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
NOx PM relay terminal 3 - s8-1 (BATT) Always Below 1 Ω
NOx PM relay terminal 3 - s8-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

7.REPLACE PARTICULATE MATTER SENSOR

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Turn the engine switch off and wait for 30 seconds.


e.

Turn the engine switch on (IG) and wait for 10 second or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



Result:
Proceed to
NEXT



NEXT

END

6.REPLACE NOX PM RELAY
a.

Replace the NOx PM relay.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE PARTICULATE MATTER SENSOR
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED