Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM › 2017.08–2021.06
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260886 KINETIC DYNAMIC SUSPENSION SYSTEM C

SUSPENSION CONTROL  KINETIC DYNAMIC SUSPENSION SYSTEM  C1831/31  Accumulator Solenoid Malfunction / Upside  C1832/32  Accumulator Solenoid Malfunction / Downside  


DESCRIPTION

The stabilizer control ECU receives information from the steering sensor, skid control ECU (speed signal) and yaw rate and acceleration sensor via CAN communication. Based on this information, the stabilizer control ECU turns the stabilizer control solenoid valve (built into the stabilizer control with accumulator housing assembly) on or off.

DTC Code DTC Detection Condition Trouble Area
C1831/31
C1832/32
Either condition is met:
·

An open circuit signal is detected for a second continuously when current is not applied to the solenoid valve.

·

A short circuit signal is detected 8 seconds continuously when current is applied to the solenoid valve.


·

Harness or connector

·

Stabilizer control solenoid valve (Stabilizer control with accumulator housing assembly)

·

Stabilizer control ECU



WIRING DIAGRAM

C215168E13
5.167,1.938 5.719,2.125 0.552,0.188 10 false G123 5.156,2.146 6.615,2.354 1.458,0.208 10 false Stabilizer Control ECU 5.438,0.729 5.833,0.917 0.396,0.188 10 false SLAU 5.438,1.521 5.813,1.688 0.375,0.167 10 false SLAL 0.917,2.146 1.24,2.344 0.323,0.198 10 false R20 0.917,2.323 4.031,2.698 3.115,0.375 10 false Stabilizer Control Solenoid Valve (Stabilizer Control with Accumulator Housing Assembly) 2.729,0.604 3.125,0.792 0.396,0.188 10 false SLAU 2.75,1.406 3.125,1.573 0.375,0.167 10 false SLAL 3.208,1.406 3.375,1.583 0.167,0.177 10 false 5 3.198,0.594 3.354,0.771 0.156,0.177 10 false 6 1.656,1.635 2.917,1.823 1.26,0.188 10 false for Upper Chamber 1.656,0.875 2.906,1.031 1.25,0.156 10 false for Lower Chamber 1,1.365 1.344,1.542 0.344,0.177 10 false AUG 0.823,1.385 1,1.552 0.177,0.167 10 false 4 5.177,0.604 5.292,0.792 0.115,0.188 10 false 3 5.177,1.396 5.302,1.563 0.125,0.167 10 false 1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR VALVE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / KDSS / Data List.


f.

Select the item below in the Data List, and read the value displayed on the intelligent tester.

KDSS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Valve (Downside) Stabilizer control solenoid valve (for Lower Chamber)/
ON or OFF
ON: Stabilizer control solenoid valve closed
OFF: Stabilizer control solenoid valve open
-
Accumulator Valve (Upside) Stabilizer control solenoid valve (for Upper Chamber)/
ON or OFF
ON: Stabilizer control solenoid valve open
OFF: Stabilizer control solenoid valve closed
-


g.

Perform the Active Test of the stabilizer control ECU using the intelligent tester.

KDSS
Tester Display Test Part Control Range Diagnostic Note
Accumulator Valve (Upside) Stabilizer control solenoid valve (for Upper Chamber) Valve ON / OFF The operating sound of the solenoid (clicking sound) can be heard
ON: Data List ON
OFF: Data List OFF
When the Active Test is performed, the solenoid turns on for 3 seconds.
Accumulator Valve (Downside) Stabilizer control solenoid valve (for Lower Chamber) Valve ON / OFF The operating sound of the solenoid (clicking sound) can be heard
ON: Data List ON
OFF: Data List OFF
When the Active Test is performed, the solenoid turns on for 3 seconds.


h.

Check that the solenoid operating sound can be heard, and that the Data List display changes between ON and OFF in response to the Active Test.


OK:

Solenoid operating sound can be heard and display changes between ON and OFF in response to Active Test.



OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - STABILIZER CONTROL SOLENOID VALVE)
2.RECONFIRM DTC

b.

Check for DTCs (See page Suspension>SUSPENSION CONTROL>KINETIC DYNAMIC SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE STABILIZER CONTROL ECU

B

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - STABILIZER CONTROL SOLENOID VALVE)
a.

Disconnect the stabilizer control ECU connector.


b.

Disconnect the Stabilizer control with accumulator housing assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-3 (SLAU) - R20-6 (SLAU) Always Below 1 Ω
G123-3 (SLAU) - Body ground Always 10 kΩ or higher
G123-1 (SLAL) - R20-5 (SLAL) Always Below 1 Ω
G123-1 (SLAL) - Body ground Always 10 kΩ or higher
R20-4 (AUG) - Body ground Always Below 1 Ω




OK

4.INSPECT STABILIZER CONTROL SOLENOID VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STABILIZER CONTROL SOLENOID VALVE
a.

Disconnect the Stabilizer control with accumulator housing assembly connector.


b.
C215163E04
0.656,1.719 0.781,1.719 0.781,1.719 1.156,1.385 false 2.302,1.885 2.083,1.885 2.083,1.885 1.635,1.396 false 1.656,0.385 1.438,0.385 1.438,0.385 1.438,1.292 false 0.354,0.115 0.604,0.323 0.25,0.208 10 false *a 1.688,0.302 2.094,0.469 0.406,0.167 10 false SLAL 0.177,1.635 0.583,1.802 0.406,0.167 10 false SLAU 2.354,1.792 2.76,1.958 0.406,0.167 10 false AUG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
C1831/31 (for Upper Chamber)
Tester Connection Condition Specified Condition
5 (SLAL) - 4 (AUG) 25°C (77°F) 24.3 to 25.7 Ω

C1832/32 (for Lower Chamber)
Tester Connection Condition Specified Condition
6 (SLAU) - 4 (AUG) 25°C (77°F) 24.3 to 25.7 Ω



Text in Illustration
*a Component without harness connected
(Stabilizer Control with Accumulator Housing Assembly)

c.

Check for an operating sound of the stabilizer control solenoid valve.

i.
C215165E01
0.164,0.114 0.429,0.386 0.266,0.272 10 *a 0.172,0.675 0.544,0.827 0.371,0.152 10 SLAL 2.085,0.46 2.456,0.612 0.371,0.152 10 AUG 0.632,0.768 0.924,0.768 0.924,0.768 1.368,1.26 false 2.033,0.547 1.732,0.547 1.732,0.547 1.652,1.269 false

for Upper Chamber:

Connect terminal 5 (SLAL) to the positive (+) battery terminal, and terminal 4 (AUG) to the negative (-) battery terminal.

OK:

An operating sound (click sound) can be heard.


Text in Illustration
*a Component without harness connected
(Stabilizer Control with Accumulator Housing Assembly)


ii.
C215164E01
0.123,0.131 0.399,0.352 0.276,0.221 10 *a 0.176,0.748 0.603,0.904 0.427,0.156 10 SLAU 2.092,0.447 2.519,0.603 0.427,0.156 10 AUG 0.683,0.836 0.807,0.836 0.807,0.836 1.137,1.272 false 2.056,0.544 1.716,0.544 1.716,0.544 1.667,1.272 false

for Lower Chamber:

Connect terminal 6 (SLAU) to the positive (+) battery terminal, and terminal 4 (AUG) to the negative (-) battery terminal.

OK:

An operating sound (click sound) can be heard.


Text in Illustration
*a Component without harness connected
(Stabilizer Control with Accumulator Housing Assembly)




OK

REPLACE STABILIZER CONTROL ECU

NG

REPLACE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY