Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side. (for Manual Seat, Power Seat)
The procedure listed below is for the RH side. (for Walk in Seat Type)
73920A
1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY
The nuts must not be reused.
Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.
Use the same procedure for the RH and LH sides.
Install the front seat side airbag assembly with 2 new nuts.
Attach the 2 clamps.
2.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Use the same procedure for the RH and LH sides.
Temporarily install the separate type front seatback cover with pad.
Attach the 4 claws to install the 2 front seat headrest supports.
Install the front seatback cover bracket with the nut.
For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
Check that the strap is not twisted after installing the bracket.
Install the bracket securely.
w/o Seatback Board:
Close the 2 fasteners, and then close the seatback cover.
| *A | for Cloth Seat | *B | for Leather Seat |
Using hog ring pliers, install 3 new hog rings.
| *1 | Hog Ring Pliers |
Be sure to securely install the hog rings as shown in the illustration.
w/ Seatback Board:
Using hog ring pliers, install 5 new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Attach the hooks.
Connect the seat heater connector and attach the wire harness clamp.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
73920A
3.CONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY
for Manual Seat, Power Seat:
Connect the airbag wire harness.
Attach the fastening tape and close the cover.
Attach the 3 airbag wire harness clamps.
Attach the claw and connect the airbag connector.
for Walk in Seat Type:
Connect the airbag wire harness.
Attach the fastening tape and close the cover.
Attach the 4 airbag wire harness clamps.
Attach the claw and connect the airbag connector.
w/o Seatback Board:
Install the rubber band to the seat cushion spring.
71706B
4.INSTALL FRONT SEATBACK BOARD CLIP (w/ Seatback Board)
71706
5.INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)
6.INSTALL FRONT SEAT ASSEMBLY
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
for Walk in Seat Type: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>INSTALLATION)
72138B
7.INSTALL SEAT TRACK COVER LH
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
72158
8.INSTALL INNER SEAT TRACK BRACKET COVER LH
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
72124
9.INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
72128A
10.INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
72137B
11.INSTALL SEAT TRACK COVER RH (for Walk in Seat Type)
72157A
12.INSTALL INNER SEAT TRACK BRACKET COVER RH (for Walk in Seat Type)
72123A
13.INSTALL FRONT SEAT OUTER TRACK BRACKET COVER RH (for Walk in Seat Type)
72127A
14.INSTALL FRONT SEAT INNER TRACK BRACKET COVER RH (for Walk in Seat Type)
71910A
15.INSTALL FRONT SEAT HEADREST ASSEMBLY
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
for Walk in Seat Type: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>INSTALLATION)
16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
17. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
18.CHECK SRS WARNING LIGHT
Check the SRS warning light (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
19.INSPECT FRONT SEAT ASSEMBLY
for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION)
for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION)
for Walk in Seat Type: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>INSTALLATION)