After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "6" (S6 range) using the transmission control switch.
Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Sports Mode Selection SW | Sport mode select switch status/
ON or OFF |
·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status/
ON or OFF |
·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status/
ON or OFF |
·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SFTU) - 5 (E) | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| 1 (SFTD) - 5 (E) | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| 2 (SFTU) - 5 (E) | Shift lever not held in "+" | 10 kΩ or higher |
| 1 (SFTD) - 5 (E) | Shift lever not held in "-" | 10 kΩ or higher |
| *a | Component without harness connected
(Transmission Control Switch) |
OK
NG
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G47-5 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Transmission Control Switch) |
OK
NG
Disconnect the ECM connector.
w/ Shift Paddle Switch:
Disconnect the spiral cable sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-15 (SFTU) - Body ground | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| G56-9 (SFTD) - Body ground | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| G56-15 (SFTU) - Body ground | Shift lever not held in "+" | 10 kΩ or higher |
| G56-9 (SFTD) - Body ground | Shift lever not held in "-" | 10 kΩ or higher |
| *a | Rear view of wire harness connector
(to ECM) |
OK
NG
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IG) - 7 (S) | Shift lever in S, "+" or "- " | Below 1 Ω |
| 3 (IG) - 7 (S) | Shift lever not in S, "+" or "-" | 10 kΩ or higher |
| *a | Component without harness connected
(Transmission Control Switch) |
OK
NG
Disconnect the transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G47-3 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| G47-3 (IG) - Body ground | Engine switch off | Below 1 V |
| *a | Front view of wire harness connector
(to Transmission Control Switch) |
OK
NG
Disconnect the G47 transmission control switch connector.
Disconnect the G56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G47-7 (S) - G56-22 (S) | Always | Below 1 Ω |
| G47-7 (S) - Body ground | Always | 10 kΩ or higher |
| G56-22 (S) - Body ground | Always | 10 kΩ or higher |
OK
NG