Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › from 2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "6" (S6 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM

C326262E72
0.344,2.917 1.99,3.375 1.646,0.458 10 false from ECU-IG NO. 1 Fuse 3.635,2.229 4.25,2.427 0.615,0.198 10 false SFTU 5.427,2.24 6.042,2.438 0.615,0.198 10 false SFTU 2.563,3.406 3.177,3.604 0.615,0.198 10 false G47 2.573,3.646 4.625,4.042 2.052,0.396 10 false Transmission Control Switch 5.302,3.844 5.917,4.042 0.615,0.198 10 false G184 5.844,3.885 6.344,4.167 0.5,0.281 10 false ECM 2.719,2.813 3.333,3.01 0.615,0.198 10 false IG 2.729,1.635 3.344,1.833 0.615,0.198 10 false E 2.563,2.802 2.875,3 0.313,0.198 10 false 3 2.563,1.635 2.875,1.833 0.313,0.198 10 false 5 5.177,2.24 5.49,2.438 0.313,0.198 10 false 21 4.073,2.823 4.385,3.021 0.313,0.198 10 false 7 4.063,2.24 4.375,2.438 0.313,0.198 10 false 2 4.063,1.656 4.375,1.854 0.313,0.198 10 false 1 6.042,2.042 6.5,2.24 0.458,0.198 10 false 12 V 6.042,2.625 6.5,2.823 0.458,0.198 10 false 12 V 0.781,0.573 3.354,0.927 2.573,0.354 10 false to Shift Paddle Switch (Transmission Shift Switch Assembly)* 0.135,4.177 1.854,4.354 1.719,0.177 10 false *: w/ Shift Paddle Switch 5.438,2.833 6.052,3.031 0.615,0.198 10 false S 5.177,1.635 5.49,1.833 0.313,0.198 10 false 20 5.469,1.646 6.083,1.844 0.615,0.198 10 false SFTD 5.177,2.823 5.49,3.021 0.313,0.198 10 false 13 3.865,2.813 4.479,3.01 0.615,0.198 10 false S 3.635,1.667 4.25,1.865 0.615,0.198 10 false SFTD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Engine
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-


Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Engine
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-


Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C203344C23
1.833,0.75 2.167,0.188 false 1.969,0.781 2.552,0.563 false 2.604,1.25 1.958,0.948 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.198,0.115 2.708,0.313 0.51,0.198 10 false SFTU 2.594,0.479 3.104,0.677 0.51,0.198 10 false SFTD 2.667,1.177 2.844,1.375 0.177,0.198 10 false E
*a Component without harness connected
(Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
2 (SFTU) - 5 (E) Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
C203343C26
0.563,0.927 0.938,1.219 0.375,0.292 0.948,1.781 1.458,1.375 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.625,1 0.927,1.188 0.302,0.188 10 false G47 0.844,1.802 1.208,2 0.365,0.198 10 false E
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) inthe table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G47-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C318001C26
2.229,0.26 2.615,0.521 0.385,0.26 1.927,2.771 2.479,1.99 true 2.896,2.771 2.552,1.99 true 1.677,2.823 2.406,3 0.729,0.177 10 false 21 (SFTU) 2.25,0.302 2.823,0.469 0.573,0.167 10 false G184 0.125,0.115 0.448,0.281 0.323,0.167 10 false *a 2.615,2.833 3.375,3.063 0.76,0.229 10 false 20 (SFTD)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

w/ Shift Paddle Switch:

Disconnect the spiral cable sub-assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-21 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
G184-20 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
G184-21 (SFTU) - Body ground Shift lever not held in "+" 10 kΩ or higher
G184-20 (SFTD) - Body ground Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C203344C24
1.083,1.5 1.646,1 true 1.063,0.229 1.625,0.76 true 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 0.896,0.156 1.125,0.406 0.229,0.25 10 false IG 0.958,1.417 1.188,1.667 0.229,0.25 10 false S
*a Component without harness connected
(Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C203343C25
0.563,0.927 0.938,1.219 0.375,0.292 1.844,1.073 2.354,0.667 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.615,0.979 0.917,1.167 0.302,0.188 10 false G47 2.385,0.542 2.75,0.74 0.365,0.198 10 false IG
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G47-3 (IG) - Body ground Ignition switch ON 11 to 14 V
G47-3 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G47-7 (S) - G184-13 (S) Always Below 1 Ω
G47-7 (S) - Body ground Always 10 kΩ or higher
G184-13 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR