Refer to DTC P023A12.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P023A12
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P023A11 | Charge Air Cooler Coolant Pump Control Circuit Short to Ground | When the electric water pump assembly speed is below 10 rpm, the IWPI input is continuously equal to or less than the judgment value for 14.5 seconds or more.
(1 trip detection logic) |
·
Open or short in electric water pump assembly circuit ·
Electric water pump assembly ·
EFI MAIN NO. 2 relay ·
ECM |
Comes on | DTC stored | SAE Code: P2CA2 |
| DTC No. | Data List |
|---|---|
| P023A11 | ·
Intercooler Water Pump Speed ·
Intercooler Water Pump |
The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.
A 4 Hz duty signal (IWPI) is output even when the pump is stopped. The ECM then converts the electric water pump assembly rotational duty signal (IWPI) into the speed and checks that it is 160 rpm when the pump is stopped.
If the electric water pump assembly speed is below 10 rpm and the IWPI input level is low this DTC is stored.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P023A11 | After fully warming up, increase and maintain the engine speed so that the intercooler water pump duty ratio is 30% or more for 3 seconds or longer. |
Refer to DTC P023A12.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P023A12
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.
Perform the Active Test. Check that the electric water pump assembly is operating (vibrating).
The electric water pump assembly is operating (vibrating).
Use a sound scope if the operation is difficult to check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Electric Water Pump Assembly) |
Disconnect the electric water pump assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B15-2 (NWP) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric water pump assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B15-2 (NWP) - C150-14 (IWPI) | Always | Below 1 Ω |
| B15-2 (NWP) or C150-14 (IWPI) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B15-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Electric Water Pump Assembly) |
Disconnect the electric water pump assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B15-4 (+BWP) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 integration relay from the engine room relay block.
Disconnect the electric water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1W-3 - B15-4 (+BWP) | Always | Below 1 Ω |
| 1W-3 or B15-4 (+BWP) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (EFI MIAN NO. 2 relay).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-7 - 1W-8 | Always | Below 1 Ω |
| 1W-4 - Body ground | Always | Below 1 Ω |
| 1V-7 or 1W-8 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG