Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P023A15  Charge Air Cooler Coolant Pump Control Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P023A12.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P023A12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P023A15 Charge Air Cooler Coolant Pump Control Circuit Short to Battery or Open When the electric water pump assembly speed is below 10 rpm, the IWPI input is continuously equal to or more than the judgment value for 14.5 seconds or more.
(1 trip detection logic)
·

Open or short in electric water pump assembly circuit

·

Electric water pump assembly

·

EFI MAIN NO. 2 relay

·

ECM


Comes on DTC stored SAE Code: P2CA1

Related Data List
DTC No. Data List
P023A15
·

Intercooler Water Pump Speed

·

Intercooler Water Pump



MONITOR DESCRIPTION

The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.

A 4 Hz duty signal (IWPI) is output even when the pump is stopped. The ECM then converts the electric water pump assembly rotational duty signal (IWPI) into the speed and checks that it is 160 rpm when the pump is stopped.

If the electric water pump assembly speed is below 10 rpm and the IWPI input level is high this DTC is stored.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P023A15 After fully warming up, increase and maintain the engine speed so that the intercooler water pump duty ratio is 30% or more for 3 seconds or longer.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.


d.

Perform the Active Test. Check that the electric water pump assembly is operating (vibrating).

OK:

The electric water pump assembly is operating (vibrating).


HINT:

Use a sound scope if the operation is difficult to check.



Result:
Proceed to
OK
NG



OK

2.CHECK ECM (IWPI VOLTAGE)

NG

4.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
2.CHECK ECM (IWPI VOLTAGE)
a.
A449468C23
1.49,0.385 1.927,0.667 0.438,0.281 1.167,1.635 1.583,1.219 true 1.594,0.438 2.104,0.656 0.51,0.219 11 false B15 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.906,1.677 1.365,1.875 0.458,0.198 10 false NWP
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


Disconnect the electric water pump assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B15-2 (NWP) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



NG

OK

3.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
a.
A449468C25
1.49,0.385 1.927,0.667 0.438,0.281 1.167,1.635 1.583,1.219 true 1.583,0.438 2.094,0.656 0.51,0.219 11 false B15 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.906,1.677 1.365,1.875 0.458,0.198 10 false NWP
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


Disconnect the electric water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B15-2 (NWP) - Body ground Engine switch on (IG) 0 to 3 V



Result:
Proceed to
OK
NG



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the electric water pump assembly connector.


b.
A449468C24
1.49,0.365 1.927,0.646 0.438,0.281 1,1.688 1.365,1.198 true 1.594,0.427 2.104,0.646 0.51,0.219 11 false B15 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.729,1.698 1.396,1.906 0.667,0.208 10 false GND
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B15-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)
a.
A449468C26
1.49,0.365 1.927,0.646 0.438,0.281 2.375,1.677 2.073,1.188 true 1.583,0.427 2.094,0.646 0.51,0.219 11 false B15 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 2.448,1.698 3.115,1.906 0.667,0.208 10 false +BWP
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


Disconnect the electric water pump assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B15-4 (+BWP) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ELECTRIC WATER PUMP ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ELECTRIC WATER PUMP ASSEMBLY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the electric water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-3 - B15-4 (+BWP) Always Below 1 Ω
1W-3 or B15-4 (+BWP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 2 RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN NO. 2 relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR

NG

REPLACE NO. 1 INTEGRATION RELAY

8.CHECK HARNESS AND CONNECTOR
a.

Remove the No. 1 integration relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-7 - 1W-8 Always Below 1 Ω
1W-4 - Body ground Always Below 1 Ω
1V-7 or 1W-8 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR