Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.
Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.
The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P050031 | Vehicle Speed Sensor "A" No Signal | for automatic transmission: Condition (a) is met for 5 seconds or more:
(a) While vehicle being driven, no vehicle speed sensor signal transmitted to ECM. (1 trip detection logic) for manual transmission: Conditions (a) and (b) are met for 6.2 seconds or more: (a) The fuel-cut operation is being performed. (b) No speed signal is input to the ECM. (2 trip detection logic) |
·
Open or short in speed signal circuit ·
Combination meter assembly ·
ECM |
Comes on | DTC stored | SAE Code: P0500 |
| DTC No. | Data List |
|---|---|
| P050031 | Vehicle Speed |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P050031 | Drive the vehicle at 10 km/h (6.25 mph) or more and perform a fuel cut |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the GTS.
| Result | Proceed to |
|---|---|
| Values displayed on GTS and speedometer display not equal | A |
| Values displayed on GTS and speedometer display equal | B |
A
B
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G304-19 (+S) - G184-10 (SPD) | Always | Below 1 Ω |
| G304-19 (+S) or G184-10 (SPD) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the circuits that send vehicle speed signals to this system in the combination meter system.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch off and wait for 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine.
Drive the vehicle at 10 km/h (6.25 mph) or more and perform a fuel cut.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the pending DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT