Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2020.08–2021.06
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU assembly which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU assembly. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU assembly. The pulse signal is created by switching the transistor in the skid control ECU assembly on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU assembly. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the skid control ECU assembly. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

B598540E02
4.99,3.729 6.927,3.938 1.938,0.208 10 false Combination Meter Assembly 4.99,3.354 6.927,3.563 1.938,0.208 10 false G304*1 4.99,3.552 5.417,3.719 0.427,0.167 10 false G6*2 5.25,2.625 5.677,2.792 0.427,0.167 10 false +S 5.24,0.271 5.667,0.438 0.427,0.167 10 false SI 0.167,0.938 2.104,1.146 1.938,0.208 10 false Brake Actuator Assembly*10 0.104,2.188 2.042,2.396 1.938,0.208 10 false Master Cylinder Solenoid*11 4.792,0.125 5.219,0.292 0.427,0.167 10 false 18*1 4.792,2.615 5.219,2.781 0.427,0.167 10 false 32*2 0.167,0.771 0.594,0.938 0.427,0.167 10 false A6 0.094,1.99 0.521,2.156 0.427,0.167 10 false A7 0.177,3.271 3.021,3.5 2.844,0.229 10 false Stereo Component Amplifier Assembly*7 0.188,4.438 3,4.677 2.813,0.24 10 false Windshield Wiper Relay Assembly*6 0.177,4.271 2.115,4.479 1.938,0.208 10 false G210 0.177,3.115 2.115,3.323 1.938,0.208 10 false H105 5.115,5.396 6.844,5.781 1.729,0.385 10 false Radio and Display Receiver Assembly*8 5.083,8.104 7.01,8.344 1.927,0.24 10 false Radio Receiver Assembly*9 5.104,5.219 5.531,5.385 0.427,0.167 10 false H92 5.083,7.917 5.51,8.083 0.427,0.167 10 false H47 5.396,4.521 5.823,4.688 0.427,0.167 10 false SPD 5.396,7.26 5.823,7.427 0.427,0.167 10 false SPD 5.104,4.51 5.531,4.677 0.427,0.167 10 false 27 5.125,7.25 5.552,7.417 0.427,0.167 10 false 17 0.104,5.531 2.917,5.771 2.813,0.24 10 false *1: except 5L-E 0.104,5.865 2.917,6.104 2.813,0.24 10 false *2: for 5L-E 0.104,6.208 2.917,6.448 2.813,0.24 10 false *3: for LHD 0.104,6.531 2.917,6.771 2.813,0.24 10 false *4: for RHD, LH Side Type 0.104,6.865 2.917,7.104 2.813,0.24 10 false *5: for RHD, RH Side Type 0.104,7.198 2.917,7.438 2.813,0.24 10 false *6: w/ Auto Wipre System 0.094,7.521 2.906,7.76 2.813,0.24 10 false *7: w/ Stereo Component Amplifier 0.083,7.854 3.958,8.167 3.875,0.313 10 false *8: w/ Audio and Visual System (for Radio and Display Type) 0.104,8.188 4.167,8.469 4.063,0.281 10 false *9: w/ Audio and Visual System (for Radio Receiver Type) 1.906,2.625 3.844,2.833 1.938,0.208 10 false 11 0.927,1.469 2.865,1.677 1.938,0.208 10 false SP1 0.969,0.292 2.906,0.5 1.938,0.208 10 false SP1 1.313,0.281 3.25,0.49 1.938,0.208 10 false 11 1.323,1.458 3.26,1.667 1.938,0.208 10 false 12 1.531,3.802 1.958,3.969 0.427,0.167 10 false SPD 1.521,2.635 1.948,2.802 0.427,0.167 10 false SPD 1.906,3.781 2.438,3.969 0.531,0.188 10 false 24 4.802,2.438 5.229,2.604 0.427,0.167 10 false 17*1 4.792,0.281 5.219,0.448 0.427,0.167 10 false 33*2 0.104,8.521 4.167,8.802 4.063,0.281 10 false *10: for 5L-E, 2TR-FE 1.938,8.521 6,8.75 4.063,0.229 10 false *11: for 1GD-FTV, 1GR-FE, 2TR-FE

B598906E03
1.094,4.635 1.906,4.833 0.813,0.198 10 false SPD*9 1.188,2.99 1.646,3.188 0.458,0.198 10 false SPDP 5.417,1.156 5.875,1.354 0.458,0.198 10 false SPD 1.094,4.448 1.552,4.646 0.458,0.198 10 false SP1*3 0.417,5.135 1.01,5.375 0.594,0.24 10 false G182*3 0.417,5.302 1.094,5.521 0.677,0.219 10 false G181*4 0.417,5.458 1.281,5.688 0.865,0.229 10 false G55*5, *8 0.417,5.625 1.375,5.854 0.958,0.229 10 false G56*5, *7 0.427,5.802 1.115,6.01 0.688,0.208 10 false G184*6 0.438,5.969 0.896,6.167 0.458,0.198 10 false ECM 1.74,4.021 2.198,4.219 0.458,0.198 10 false 25*3 1.74,4.177 2.198,4.375 0.458,0.198 10 false 23*4 1.74,4.333 2.469,4.563 0.729,0.229 10 false 12*5, *7 1.729,4.5 2.635,4.708 0.906,0.208 10 false 18*5, *8 1.74,4.656 2.198,4.854 0.458,0.198 10 false 10*6 0.125,3.438 0.583,3.635 0.458,0.198 10 false G187 0.135,3.604 1.729,3.823 1.594,0.219 10 false Telematics Transceiver*1 5.073,1.885 5.531,2.083 0.458,0.198 10 false G215 5.083,2.083 6.979,2.344 1.896,0.26 10 false Certification ECU Assembly*2 0.271,6.563 2.698,6.74 2.427,0.177 10 false *1: w/ Telematics Transceiver 0.271,6.792 2.906,6.99 2.635,0.198 10 false *2: w/ Entry and Start System 0.271,7.021 1.323,7.219 1.052,0.198 10 false *3: for 5L-E 0.271,7.26 1.365,7.479 1.094,0.219 10 false *4 for 2TR-FE 0.281,7.51 2.292,7.75 2.01,0.24 10 false *5: for 1GR-FE 0.281,7.76 1.385,7.938 1.104,0.177 10 false *6: for 1GD-FTV 0.281,8.01 2.531,8.198 2.25,0.188 10 false *7: for Automatic Transmission 0.271,8.25 2.458,8.49 2.188,0.24 10 false *8: for Manual Transmission 0.271,8.5 2.031,8.708 1.76,0.208 10 false *9: except 5L-E 1.688,3 2.146,3.198 0.458,0.198 10 false 10 5.24,1.125 5.698,1.323 0.458,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM or certification ECU (smart key ECU assembly) refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
E188997C89
0.802,0.094 1.219,0.344 0.417,0.25 0.813,0.49 1.229,0.74 0.417,0.25 2.427,1.469 2.667,0.906 2.667,0.906 2.792,0.906 true 1.896,1.625 2.438,2 2.438,2 2.76,2 true 2.854,0.833 3.292,1.042 0.438,0.208 10 false +S*1 0.177,0.198 0.427,0.396 0.25,0.198 10 false *a 0.833,0.135 1.292,0.333 0.458,0.198 10 false G304 1.292,0.115 1.75,0.313 0.458,0.198 10 false *1 0.927,0.552 1.385,0.75 0.458,0.198 10 false G6 1.313,0.51 1.771,0.708 0.458,0.198 10 false *2 2.833,1.917 3.271,2.125 0.438,0.208 10 false +S*2
*a Front view of wire harness connector
(to Combination Meter Assembly)
*1 except 5L-E
*2 for 5L-E


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (except 5L-E):
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Ignition switch ON 4.5 to 14 V


Standard Voltage (for 5L-E):
Tester Connection Switch Condition Specified Condition
G6-32 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

for 1GR-FE, 1GD-FTV:

i.

Reconnect the G304 combination meter assembly connector.


ii.
U149350C04
2.521,0.927 2.208,1.573 false 0.115,0.417 0.292,0.583 0.177,0.167 10 false *a 1.615,0.813 1.833,0.958 0.219,0.146 10 false A7 2.573,0.813 2.979,0.958 0.406,0.146 10 false SP1
*a Front view of wire harness connector
(to Skid Control ECU Assembly)


Disconnect the skid control ECU assembly connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-12 (SP1) - Body ground Ignition switch ON 11 to 14 V




b.

for 2TR-FE, 5L-E:

i.

Reconnect the G304*1, G6*2 combination meter assembly connector.

*1: for 2TR-FE

*2: for 5L-E



ii.
U170657C03
2.531,0.594 2.188,1.531 false 0.125,0.073 0.302,0.24 0.177,0.167 10 false *a 1.625,0.469 1.844,0.615 0.219,0.146 10 false A6 2.583,0.469 3.01,0.677 0.427,0.208 10 false SP1
*a Front view of wire harness connector
(to Skid Control ECU Assembly)


Disconnect the skid control ECU assembly connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-11 (SP1) - Body ground Ignition switch ON 11 to 14 V




Result:
Proceed to
OK
NG



OK

3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU ASSEMBLY)
3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
B599362C01
0.802,0.458 1.292,0.677 0.49,0.219 1.979,0.448 2.5,0.677 0.521,0.229 2.271,2.115 1.5,1.406 true 0.802,2.021 0.958,1.292 true 0.177,0.156 0.667,0.469 0.49,0.313 10 false *a 2.323,2.073 2.75,2.302 0.427,0.229 10 false SI*2 2.76,3.646 3.406,3.917 0.646,0.271 10 false GND 0.865,0.49 1.365,0.667 0.5,0.177 10 false G304 0.896,3.76 1.385,4.073 0.49,0.313 10 false A 2.135,0.479 3.417,4.615 1.281,4.135 10 false G6 1.333,0.479 1.823,0.792 0.49,0.313 10 false *1 2.563,0.479 3.052,0.792 0.49,0.313 10 false *2 0.646,2.104 1.073,2.333 0.427,0.229 10 false SI*1
*a Component with harness connected
(Combination Meter Assembly)
*1 except 5L-E
*2 5L-E


Check the input waveform.

i.

Reconnect the A7*1, A6*2 skid control ECU assembly connector.

*1:1GR-FE, 1GD-FTV

*2: 2TR-FE, 5L-E



ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal G304-18 (SI)*1, G6-33 (SI)*2 and body ground.

*1: except 5L-E

*2: for 5L-E



iv.

Turn the ignition switch to ON.


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch to ON wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SKID CONTROL ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU ASSEMBLY)

*1: except 5L-E

*2: for 5L-E

*3: for 2TR-FE, 5L-E

*4: for 1GR-FE, 1GD-FTV


a.

Disconnect the G304*1 or G6*2 combination meter assembly connector.


b.

Disconnect the A6*3 or A7*4 skid control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for 2TR-FE

*2: for 1GR-FE, 1GD-FTV


Standard Resistance (except 5L-E):
Tester Connection Condition Specified Condition
G304-18 (SI) - A6-11 (SP1)*1 Always Below 1 Ω
G304-18 (SI) - A7-12 (SP1)*2 Always Below 1 Ω
G304-18 (SI) - Other terminals and body ground Always 10 kΩ or higher


Standard Resistance (for 5L-E):
Tester Connection Condition Specified Condition
G6-33 (SI) - A6-11 (SP1) Always Below 1 Ω
G6-33 (SI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)

*1: w/ Entry and Start System

*2: w/ Stereo Component Amplifier

*3: for 1GR-FE, Automatic Transmission

*4: for 1GR-FE, Manual Transmission

*5: for 2TR-FE

*6: for 5L-E

*7: for 1GD-FTV

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)

*10: w/ Auto Wipr System

*11: w/ Telematics System


a.

Disconnect the G215*1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H105*2 stereo component amplifier assembly connector.


c.

Disconnect the G55*3, G56*4, G181*5, G182*6 or G184*7 ECM connector.


d.

Disconnect the H92 radio and display receiver assembly connector.*8


e.

Disconnect the H47 radio receiver assembly connector.*9


f.

Disconnect the G210 auto wiper switch connector.*10


g.

Disconnect the G187 telematics transceiver connector.*11


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (except 5L-E):
Tester Connection Condition Specified Condition
G304-17 (+S) - Other terminals and body ground Always 10 kΩ or higher


Standard Resistance (for 5L-E):
Tester Connection Condition Specified Condition
G6-32 (+S) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ECM (SHORT CIRCUIT IN ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (SHORT CIRCUIT IN ECM)

*1: w/ Entry and Start System

*2: w/ Stereo Component Amplifier

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Audio and Visual System (for Radio Receiver Type)

*5: w/ Auto Wipr System

*6: w/ Telematics System


a.

Reconnect the G215*1 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the H105*2 stereo component amplifier assembly connector.


c.

Reconnect the H92 radio and display receiver assembly connector.*3


d.

Reconnect the H47 radio receiver assembly connector.*4


e.

Reconnect the G210 auto wiper switch connector.*5


f.

Reconnect the G187 telematics transceiver connector.*6


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (except 5L-E):
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Ignition switch ON 4.5 to 14 V


Standard Voltage (for 5L-E):
Tester Connection Switch Condition Specified Condition
G6-32 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the ECM.



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER)
7.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER)
NOTICE:

For vehicle without a stereo component amplifier assembly, proceed to next step.


a.

Disconnect the H105 stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

8.INSPECT TELEMATICS TRANSCEIVER (SHORT CIRCUIT IN TELEMATICS TRANSCEIVER)
8.INSPECT TELEMATICS TRANSCEIVER (SHORT CIRCUIT IN TELEMATICS TRANSCEIVER)
NOTICE:

For vehicle without a telephone transceiver assembly, proceed to next step.


a.

Disconnect the G187 telematics transceiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the telephone transceiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE TELEMATICS TRANSCEIVER

NG

9.INSPECT CERTIFICATION ECU (SHORT CIRCUIT IN CERTIFICATION ECU)
9.INSPECT CERTIFICATION ECU (SHORT CIRCUIT IN CERTIFICATION ECU)
NOTICE:

For vehicle without a certification ECU, proceed to next step.


a.

Disconnect the G215 certification ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the certification ECU (smart key ECU assembly).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

10.INSPECT WINDSHIELD WIPER RELAY ASSEMBLY (SHORT CIRCUIT IN WINDSHIELD WIPER RELAY ASSEMBLY)
10.INSPECT WINDSHIELD WIPER RELAY ASSEMBLY (SHORT CIRCUIT IN WINDSHIELD WIPER RELAY ASSEMBLY)
NOTICE:

For vehicle without a windshield wiper relay assembly, proceed to next step.


a.

Disconnect the G210 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the windshield wiper relay assembly.



Result:
Result Proceed to
OK A
NG (Audio and Visual System [for Radio and Display Type]) B
NG (w/ Audio and Visual System [for Radio Receiver Type]) C



A

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

B

REPLACE REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C