Refer to DTC P052477.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P052477
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P06DA12 | Engine Oil Pressure Control Circuit Short to Battery | While the oil pressure switching valve assembly is operating, the ECM detects high voltage for 5 seconds or more.
(1 trip detection logic) |
·
Short in oil pressure switching valve assembly circuit ·
Oil pressure switching valve assembly ·
ECM |
Does not come on | DTC stored | SAE Code: P06DC |
| P06DA14 | Engine Oil Pressure Control Circuit Short to Ground or Open | While the oil pressure switching valve assembly is not operating, the ECM detects low voltage for 5 seconds or more.
(1 trip detection logic) |
·
Open or short in oil pressure switching valve assembly circuit ·
Oil pressure switching valve assembly ·
ECM |
Does not come on | DTC stored | SAE Code: P06DB |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P06DA12 | 5 seconds or more after engine is started |
| P06DA14 | Engine switch on (IG) for 5 seconds or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the oil pressure switching valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCHING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the oil pressure switching valve assembly connector.
| *a | Front view of wire harness connector
(to Oil Pressure Switching Valve Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C130-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the oil pressure switching valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C130-1 - C150-13 (EOPV) | Always | Below 1 Ω |
| C130-1 or C150-13 (EOPV) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
If the voltage at the oil pressure switching valve assembly connector is not 11 to 14 V, repair or replace the harness and connector between the oil pressure switching valve assembly and No. 1 integration relay.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch on (IG) for 5 seconds or more.
Start the engine and wait for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure switching valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCHING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT