Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P052477  Engine Oil Pressure Too Low (Severe)  


DESCRIPTION

The oil pressure control system reduces and increases engine oil pressure using the oil pressure switching valve in the timing gear case assembly. When the engine speed reaches 2600 rpm while racing the engine after warming it up, the oil pressure switching valve operates and the engine oil pressure system changes from low pressure control mode to high pressure control mode. When the engine speed drops to 2400 rpm, the engine oil pressure system changes from high pressure control mode to low pressure control mode. The oil pressure sender gauge assembly detects the engine oil pressure.

A246647E04
3.635,2.271 3.844,2.583 3.844,2.583 3.99,2.583 true 3.573,1.781 3.792,1.385 3.792,1.385 3.958,1.385 true 5.188,0.594 5.396,0.906 5.396,0.906 5.542,0.906 true 0.521,0.531 1.198,0.958 0.677,0.427 10 false Engine Oil Pressure 4.052,2.521 5.198,2.719 1.146,0.198 10 false Low Oil Pressure 5.625,0.833 6.865,1.031 1.24,0.198 10 false High Oil Pressure 3.458,3.188 4.406,3.385 0.948,0.198 10 false Engine Speed 4.01,1.302 6.188,1.5 2.177,0.198 10 false Oil Jet Valve-opening Pressure

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052477 Engine Oil Pressure Too Low (Severe) Conditions (a) and (b) continue for 8 seconds or more:

(a) 0.3 seconds have elapsed after sending a command to change from low oil pressure control mode to high oil pressure control mode.

(b) The oil pressure control system does not change to high oil pressure control mode.


(1 trip detection logic)
·

Short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

Oil pressure switching valve assembly

·

ECM

·

Oil pump assembly (Timing chain case assembly)

·

Engine oil amount insufficient

·

EFI MAIN NO. 2 relay


Comes on DTC stored SAE Code: P0524

Related Data List
DTC No. Data List
P052477
·

Engine Oil Pressure

·

Engine Oil Pressure VSV



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052477 After warming up the engine, race the engine at 2600 rpm or higher.*
*: Using the GTS, the oil pressure control system can be inspected by performing Engine Oil Pressure Control Check. Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.
HINT:

Checking the state of the oil level warning light and oil pressure warning light will help in understanding why this DTC was stored (Click here (Click here)).



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

An output DTC does not necessarily indicate that there is a malfunction. DTCs may have been stored due to an insufficient engine oil amount even though the oil level warning light is currently not illuminated, such as when engine oil is added by the customer.



PROCEDURE

1.CHECK ENGINE OIL LEVEL
a.

Check the engine oil level.


b.

Check the state of the oil level warning light.


Result:
Result Proceed to
Engine oil level is low and oil level warning light is illuminated A
Engine oil level is within the specified range and oil level warning light is not illuminated B


HINT:

If the oil level warning light is not illuminated even though the engine oil level is lower than the Low mark, or the oil level warning light is illuminated even though the engine oil level is within the specified range, inspect the oil level sensor and related parts for malfunctions.



A

2.CHECK ENGINE OIL LEAKS

B

4.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
2.CHECK ENGINE OIL LEAKS
a.

Check for engine oil leaks.

Result:

If there are engine oil leaks, perform repairs.



Result:
Proceed to
NEXT



NEXT

3.ADD ENGINE OIL
3.ADD ENGINE OIL
a.

Add engine oil.


Result:
Proceed to
NEXT



NEXT

4.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
4.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.


e.

Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check the difference.

OK:

50 kPa or higher



Result:
Proceed to
OK
NG



NG

5.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)

OK

END

5.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
a.

Disconnect the oil pressure switching valve assembly connector.

NOTICE:
·

Make sure that the engine is stopped before disconnecting the connector of the oil pressure switching valve assembly.

·

Make sure that the disconnected connector does not get caught in moving engine parts.




b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.


f.

Check the engine oil pressure value.

Result:
Result Proceed to
Engine oil pressure rises to between 250 and 510 kPa A
Except above B


HINT:

Low oil pressure control mode is not performed when the connector of the oil pressure switching valve assembly is disconnected. Therefore, if the measurement results from Engine Oil Pressure Control Check all indicate oil pressure values which are high, it can be determined that there is an electrical malfunction.




A

6.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 2 RELAY)

B

11.INSPECT ENGINE OIL PRESSURE
6.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 2 RELAY)

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - OIL PRESSURE SWITCHING VALVE ASSEMBLY - ECM)

NG

10.REPLACE NO. 1 INTEGRATION RELAY
7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - OIL PRESSURE SWITCHING VALVE ASSEMBLY - ECM)
a.

Remove the No. 1 integration relay.


b.

Disconnect the oil pressure switching valve assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C130-2 - Body ground* Always 10 kΩ or higher
C130-1 - Body ground Always 10 kΩ or higher


HINT:

*: Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the oil pump assembly.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE NO. 1 INTEGRATION RELAY
a.

Replace the No. 1 integration relay.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.INSPECT ENGINE OIL PRESSURE

Result:
Proceed to
OK
NG



OK

12.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

13.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
12.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Replace the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
a.

Replace the oil pressure switching valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
14.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.


e.

Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check the difference.

OK:

50 kPa or higher



Result:
Proceed to
OK
NG



OK

END

NG

15.INSPECT OIL PUMP ASSEMBLY (TIMING CHAIN CASE ASSEMBLY)
15.INSPECT OIL PUMP ASSEMBLY (TIMING CHAIN CASE ASSEMBLY)
a.

Repair or replace the oil pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PUMP>REMOVAL

HINT:

If the oil pressure does not rise after disconnecting the connector of the oil pressure switching valve assembly, or if the oil pressure changes, but the difference between the low oil pressure and high oil pressure is small, a mechanical malfunction is probably the cause.

·

The sleeve is locked due to foreign matter.

·

The oil pressure relief valve is locked due to foreign matter.

·

The check valve is stuck.




Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine and warm it up.


g.

Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.


h.

Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check that the oil pressure has risen.


Result:
Proceed to
NEXT



NEXT

END