| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P167A87 | Injector #1 Missing Message | Communication between the ECM and injector assembly is lost for 10 seconds or more.
(2 trip detection logic) |
·
No. 1 Injector assembly ·
Harness and connector |
Comes on | DTC stored | SAE Code: P167A |
| P167B87 | Injector #2 Missing Message | Communication between the ECM and injector assembly is lost for 10 seconds or more.
(2 trip detection logic) |
·
No. 2 Injector assembly ·
Harness and connector |
Comes on | DTC stored | SAE Code: P167B |
| P167C87 | Injector #3 Missing Message | Communication between the ECM and injector assembly is lost for 10 seconds or more.
(2 trip detection logic) |
·
No. 3 Injector assembly ·
Harness and connector |
Comes on | DTC stored | SAE Code: P167C |
| P167D87 | Injector #4 Missing Message | Communication between the ECM and injector assembly is lost for 10 seconds or more.
(2 trip detection logic) |
·
No. 4 Injector assembly ·
Harness and connector |
Comes on | DTC stored | SAE Code: P167D |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P167A87
P167B87 P167C87 P167D87 |
Engine switch on (IG) for 3 minutes or more |
If the ECM detects that there is a communication problem with an injector for a certain amount of time continuously, it illuminates the MIL.
A DTC is assigned for each cylinder. However, the cylinders cannot be distinguished. If there is no problem with the communication line, replace all the injector assemblies.
Refer to DTC P13A011.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P13A011
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P167A87, P167B87, P167C87 and P167D87 are output | A |
| DTC P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13C013, P13C513, P13CA13, P13D013 and/or P167A87, P167B87, P167C87, P167D87 are output | B |
A
B
Fuel pressure sensor circuit:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P13A011
Fuel temperature sensor circuit:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P13C013
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C191-5 (CINJ) - C149-17 (CINJ) | Always | Below 1 Ω |
| C192-5 (CIJ2) - C149-17 (CINJ) | Always | Below 1 Ω |
| C193-5 (CIJ3) - C149-17 (CINJ) | Always | Below 1 Ω |
| C194-5 (CIJ4) - C149-17 (CINJ) | Always | Below 1 Ω |
| C191-5 (CINJ) or C149-17 (CINJ) - Body ground and other terminals | Always | 200 kΩ or higher |
| C192-5 (CIJ2) or C149-17 (CINJ) - Body ground and other terminals | Always | 200 kΩ or higher |
| C193-5 (CIJ3) or C149-17 (CINJ) - Body ground and other terminals | Always | 200 kΩ or higher |
| C194-5 (CIJ4) or C149-17 (CINJ) - Body ground and other terminals | Always | 200 kΩ or higher |
Reconnect the injector assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector assembly connector.
| *1 | Ohmmeter |
| *a | Component without harness connected
(Injector Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (CINJ) - 1 (EIJ1) | Always | 600 to 1400 kΩ |
| 5 (CIJ2) - 1 (EIJ2) | Always | 600 to 1400 kΩ |
| 5 (CIJ3) - 1 (EIJ3) | Always | 600 to 1400 kΩ |
| 5 (CIJ4) - 1 (EIJ4) | Always | 600 to 1400 kΩ |
If there is an injector assembly that is outside the specified range, only replace that injector assembly.
Even when the resistance is within the specified range, the injector assembly may be malfunctioning. Therefore, if all of the injector assemblies are within the specified range, replace all of the injector assemblies.
Reconnect the injector assembly connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) for 3 minutes or more.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P167A87, P167B87, P167C87 or P167D87.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, turn the engine switch on (IG) for 3 minutes or more, and then check "All Readiness" again.
| Proceed to |
|---|
| NEXT |
NEXT