A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure. A semiconductor is used in the fuel pressure sensor. The semiconductor changes its internal resistance value according to the fuel pressure, and as a result, the output voltage is proportional to the fuel pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P13A011 | Fuel Pressure Sensor #1(Sub CPU) Circuit Short to Ground | Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13A1 |
| P13A015 | Fuel Pressure Sensor #1(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13A2 |
| P13A02A | Fuel Pressure Sensor #1(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13A3 |
| P13A511 | Fuel Pressure Sensor #2(Sub CPU) Circuit Short to Ground | Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13A6 |
| P13A515 | Fuel Pressure Sensor #2(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13A7 |
| P13A52A | Fuel Pressure Sensor #2(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13A8 |
| P13AA11 | Fuel Pressure Sensor #3(Sub CPU) Circuit Short to Ground | Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13AB |
| P13AA15 | Fuel Pressure Sensor #3(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13AC |
| P13AA2A | Fuel Pressure Sensor #3(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13AD |
| P13B011 | Fuel Pressure Sensor #4(Sub CPU) Circuit Short to Ground | Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13B1 |
| P13B015 | Fuel Pressure Sensor #4(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13B2 |
| P13B02A | Fuel Pressure Sensor #4(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13B3 |
| P13E011 | Fuel Pressure Sensor #1(Main CPU) Circuit Short to Ground | Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.55 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13E1 |
| P13E015 | Fuel Pressure Sensor #1(Main CPU) Circuit Short to Battery or Open | Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.76 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13E2 |
| P13E511 | Fuel Pressure Sensor #4(Main CPU) Circuit Short to Ground | Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.55 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13E6 |
| P13E515 | Fuel Pressure Sensor #4(Main CPU) Circuit Short to Battery or Open | Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.76 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit ·
Fuel pressure sensor (built into injector assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P13E7 |
| DTC No. | Data List |
|---|---|
| P13A011
P13A015 P13A511 P13A515 P13AA11 P13AA15 P13B011 P13B015 |
·
Fuel Pressure #1 ·
Fuel Pressure #2 ·
Fuel Pressure #3 ·
Fuel Pressure #4 |
| P13E011
P13E015 P13E511 P13E515 |
|
| P13A02A
P13A52A P13AA2A P13B02A |
Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High). Under stable conditions, the difference between "Fuel Pressure (High)" and "Target Fuel Pressure (High)" is 5000 kPag or less.
For more information on the fuel pressure sensor and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).
If DTC P13A011, P13A015, P13A511, P13A515, P13AA11, P13AA15, P13B011, P13B015, P13E011, P13E015, P13E511 and/or P13E515 is stored, the following symptom may appear:
Lack of power due to accelerator restriction performed by fail-safe function
If DTC P13A011, P13A015, P13A511, P13A515, P13AA11, P13AA15, P13B011, P13B015, P13E011, P13E015, P13E511 and/or P13E515 is stored, "Fuel Pressure (High)" always displays -53000 kPag or 255992 kPag.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P13A011
P13A015 P13A511 P13A515 P13AA11 P13AA15 P13B011 P13B015 |
Engine switch on (IG) for 1 second or more |
| P13E011
P13E015 P13E511 P13E515 |
Engine switch on (IG) for 8 seconds or more |
| P13A02A
P13A52A P13AA2A P13B02A |
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
If the fuel pressure sensor output voltage is outside of the standard range due to an open or short in the fuel pressure sensor circuit, DTCs are stored.
If a DTC is stored, the ECM enters fail-safe mode, and engine output is limited only if 2 or more circuits are malfunctioning. The ECM continues operating in fail-safe mode until the engine switch is turned off.
The No. 1 injector assembly and No. 4 injector assembly have separate circuits inside the ECU and a fuel pressure sensor value is input to both the Main CPU and Sub CPU.
When there is an open circuit in EIJ or VIJ, DTC P13E015 and P13A015 are output at the same time.
If only one of them are output, there may be an open in the internal circuit of the ECM.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| "Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output* | A |
| Except above | B |
*: Fuel pressure sensor circuit DTC and Injector Internal EEPROM Malfunction circuit DTC:
Fuel pressure sensor circuit DTC: P13A02A, P13A52A, P13AA2A, P13B02A.
Injector Internal EEPROM Malfunction circuit DTC: P168A00, P168A44, P168A46, P168B00, P168B44, P168B46, P168C00, P168C44, P168C46, P168D00, P168D44, P168D46.
When there is an injector internal EEPROM malfunction, fuel pressure sensor (sub CPU) signal stuck in range and fuel temperature sensor circuit open DTCs are output at the same time.
For example, when P168A00, P168A44, P168A46 is output, P13A02A and P13C013 are output together.
A
B
| *a | Component with harness connected
(ECM) |
Disconnect the injector assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-28 (VIJ1) - C151-19 (EIJ1) | Engine switch on (IG) | 4.5 to 5.5 V |
| C152-24 (VIJ2) - C152-30 (EIJ2) | Engine switch on (IG) | 4.5 to 5.5 V |
| C152-33 (VIJ3) - C152-32 (EIJ3) | Engine switch on (IG) | 4.5 to 5.5 V |
| C152-22 (VIJ4) - C152-21 (EIJ4) | Engine switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C191-2 (VIJ1) - C151-28 (VIJ1) | Always | Below 1 Ω |
| C191-4 (PIJ1) - C151-18 (PIJ1) | Always | Below 1 Ω |
| C191-1 (EIJ1) - C151-19 (EIJ1) | Always | Below 1 Ω |
| C192-2 (VIJ2) - C152-24 (VIJ2) | Always | Below 1 Ω |
| C192-4 (PIJ2) - C152-29 (PIJ2) | Always | Below 1 Ω |
| C192-1 (EIJ2) - C152-30 (EIJ2) | Always | Below 1 Ω |
| C193-2 (VIJ3) - C152-33 (VIJ3) | Always | Below 1 Ω |
| C193-4 (PIJ3) - C152-26 (PIJ3) | Always | Below 1 Ω |
| C193-1 (EIJ3) - C152-32 (EIJ3) | Always | Below 1 Ω |
| C194-2 (VIJ4) - C152-22 (VIJ4) | Always | Below 1 Ω |
| C194-4 (PIJ4) - C152-23 (PIJ4) | Always | Below 1 Ω |
| C194-1 (EIJ4) - C152-21 (EIJ4) | Always | Below 1 Ω |
| C191-4 (PIJ1) or C151-18 (PIJ1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C191-1 (EIJ1) or C151-19 (EIJ1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C192-4 (PIJ2) or C152-29 (PIJ2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C192-1 (EIJ2) or C152-30 (EIJ2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C193-4 (PIJ3) or C152-26 (PIJ3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C193-1 (EIJ3) or C152-32 (EIJ3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C194-4 (PIJ4) or C152-23 (PIJ4) - Body ground and other terminals | Always | 10 kΩ or higher |
| C194-1 (EIJ4) or C152-21 (EIJ4) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the injector assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Perform the following when there are DTCs which are not cleared.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) for 8 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes / Clear.
Check that all DTCs have been cleared.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) for 8 seconds or more.
Start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT