The active control engine mount system decreases engine vibration at low engine speed using the vacuum switching valve sub-assembly (for engine mounting). The vacuum switching valve sub-assembly (for engine mounting) is controlled by a pulse signal transmitted to the vacuum switching valve sub-assembly (for engine mounting) from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P0A1412 | Engine Mount "A" Control Circuit High Circuit Short to Battery | Short in vacuum switching valve sub-assembly (for engine mounting)circuit and power supply circuit (2 trip detection logic). | ·
Short in vacuum switching valve sub-assembly (for engine mounting)circuit ·
Vacuum switching valve sub-assembly (for engine mounting) ·
ECM |
Does not come on | DTC stored | SAE Code: P0A16 |
| P0A1414 | Engine Mount "A" Control Circuit Low Circuit Short to Ground or Open | Open or short in vacuum switching valve sub-assembly (for engine mounting)circuit and power supply circuit
(2 trip detection logic). |
·
Open or short in vacuum switching valve sub-assembly (for engine mounting)circuit ·
Vacuum switching valve sub-assembly (for engine mounting) ·
ECM |
Does not come on | DTC stored | SAE Code: P0A15 |
The ECM monitors the output voltage while the vacuum switching valve sub-assembly (for engine mounting)is operating.
The vacuum switching valve sub-assembly (for engine mounting)turns on and off according to ON/OFF switching of a transistor inside the ECM.
If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the vacuum switching valve sub-assembly (for engine mounting)circuit and stores a DTC.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0A1412
P0A1414 |
Engine switch on (IG) for 3 seconds or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the vacuum switching valve sub-assembly (for engine mounting).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.
| *a | Front view of wire harness connector
(to Vacuum Switching Valve Sub-assembly (for Engine Mounting)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C173-1 - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C173-2 - G184-34 (ACM) | Always | Below 1 Ω |
| C173-2 or G184-34 (ACM) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
If the voltage at the vacuum switching valve sub-assembly (for engine mounting) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve sub-assembly (for engine mounting) and No. 1 integration relay.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch on (IG) for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the vacuum switching valve sub-assembly (for engine mounting).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>VACUUM SWITCHING VALVE (for Engine Mounting)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT