Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2020.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit  


DESCRIPTION

·

The radio and display receiver assembly, telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the DCM (telematics transceiver) sends power to telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the DCM (telematics transceiver).*

*: w/ Telematics Transceiver



WIRING DIAGRAM

E402703E17
5.76,1.365 6.375,1.563 0.615,0.198 10 false SNS2 1.719,1.26 2.135,1.458 0.417,0.198 10 false SNS2 1.677,1.677 2.135,1.854 0.458,0.177 10 false MACC 1.688,2 2.146,2.177 0.458,0.177 10 false MCO+ 1.719,2.354 2.177,2.531 0.458,0.177 10 false MCO- 5.781,1.771 6.24,1.948 0.458,0.177 10 false MACC 5.771,2.073 6.146,2.302 0.375,0.229 10 false MIN+ 5.771,2.417 6.146,2.646 0.375,0.229 10 false MIN- 5.771,2.792 6.271,3.021 0.5,0.229 10 false SGND 3.833,2.75 4.333,2.979 0.5,0.229 10 false * 0.552,3.063 1.958,3.521 1.406,0.458 10 false Telephone Microphone Assembly 0.573,2.906 1.979,3.365 1.406,0.458 10 false A 0.333,4.01 1.938,4.333 1.604,0.323 10 false Map Light Assembly 0.333,3.854 0.677,4.042 0.344,0.188 10 false W7 5.438,3.802 5.781,3.99 0.344,0.188 10 false H93 5.438,3.979 7.115,4.344 1.677,0.365 10 false Radio and Display Receiver Assembly 1.552,1.26 1.688,1.438 0.135,0.177 10 false 1 1.542,1.667 2,1.844 0.458,0.177 10 false 5 1.542,1.99 2,2.167 0.458,0.177 10 false 3 1.552,2.354 2.01,2.531 0.458,0.177 10 false 2 2.177,1.25 2.406,1.417 0.229,0.167 10 false 14 2.188,1.667 2.417,1.833 0.229,0.167 10 false 11 2.198,2 2.427,2.167 0.229,0.167 10 false 12 2.198,2.344 2.427,2.51 0.229,0.167 10 false 13 5.5,2.688 5.844,2.875 0.344,0.188 10 false 24 5.49,1.979 5.833,2.167 0.344,0.188 10 false 21 5.49,2.344 5.833,2.531 0.344,0.188 10 false 22 5.51,1.635 5.854,1.823 0.344,0.188 10 false 23 5.51,1.24 5.854,1.427 0.344,0.188 10 false 25 2.458,4.469 4.167,4.667 1.708,0.198 10 false *: Shielded 0.229,0.156 3.875,0.531 3.646,0.375 12 false w/o Telematics Transceiver:


E402702E37
5.729,1.188 6.344,1.385 0.615,0.198 10 false SNS2 5.74,1.833 6.354,2.031 0.615,0.198 10 false MIN+ 5.74,2.26 6.354,2.458 0.615,0.198 10 false MIN- 5.771,2.802 6.385,3 0.615,0.198 10 false SGND 5.104,2.698 5.719,2.896 0.615,0.198 10 false * 0.115,0.094 3.729,0.365 3.615,0.271 12 false w/ Telematics Transceiver: 0.521,2.906 0.802,3.083 0.281,0.177 10 false A 0.5,3.063 1.927,3.469 1.427,0.406 10 false Telephone Microphone Assembly 1.646,1.094 2.094,1.271 0.448,0.177 10 false SNS2 1.615,1.677 2.115,1.854 0.5,0.177 10 false MACC 1.625,2 2.125,2.177 0.5,0.177 10 false MCO+ 1.656,2.375 2.156,2.552 0.5,0.177 10 false MCO- 1.469,2.01 1.75,2.188 0.281,0.177 10 false 3 1.479,1.094 1.76,1.271 0.281,0.177 10 false 1 1.469,1.656 1.75,1.833 0.281,0.177 10 false 5 1.479,2.344 1.76,2.521 0.281,0.177 10 false 2 2.094,1.094 2.385,1.302 0.292,0.208 10 false 14 2.083,1.979 2.375,2.188 0.292,0.208 10 false 12 2.094,1.646 2.385,1.854 0.292,0.208 10 false 11 2.094,2.344 2.385,2.552 0.292,0.208 10 false 13 3.375,1.76 3.875,1.938 0.5,0.177 10 false MCVD 3.375,2.094 3.875,2.271 0.5,0.177 10 false MCI+ 3.375,2.417 3.875,2.594 0.5,0.177 10 false MCI- 3.385,2.792 3.885,2.969 0.5,0.177 10 false SGND 0.281,3.833 0.688,4.073 0.406,0.24 10 false W7 0.25,4.031 2.479,4.292 2.229,0.26 10 false Map Light Assembly 2.781,3.604 5.406,3.813 2.625,0.208 10 false DCM (Telematics Transceiver) 2.771,3.417 5,3.677 2.229,0.26 10 false G187 5.375,3.938 7.104,4.365 1.729,0.427 10 false Radio and Display Receiver Assembly 5.375,3.792 7.104,4.219 1.729,0.427 10 false H93 5.458,1.083 6.073,1.281 0.615,0.198 10 false 25 5.458,1.729 6.073,1.927 0.615,0.198 10 false 21 5.458,2.146 6.073,2.344 0.615,0.198 10 false 22 5.479,2.635 6.094,2.833 0.615,0.198 10 false 24 4.135,1.823 4.635,2 0.5,0.177 10 false MCO+ 4.146,2.229 4.646,2.406 0.5,0.177 10 false MCO- 3.094,1.656 3.594,1.833 0.5,0.177 10 false 33 3.104,1.979 3.604,2.156 0.5,0.177 10 false 34 3.115,2.344 3.615,2.521 0.5,0.177 10 false 35 3.115,2.677 3.615,2.854 0.5,0.177 10 false 32 4.646,1.719 5.146,1.896 0.5,0.177 10 false 18 4.667,2.156 5.167,2.333 0.5,0.177 10 false 19 2.438,4.385 4.667,4.646 2.229,0.26 10 false *: Shielded 2.625,2.729 3.24,2.927 0.615,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
NG (w/o Telematics Transceiver) A
NG (w/ Telematics Transceiver) B
OK C



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

C

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-25 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H93-23 (MACC) - W7-11 (MACC) Always Below 1 Ω
H93-21 (MIN+) - W7-12 (MCO+) Always Below 1 Ω
H93-22 (MIN-) - W7-13 (MCO-) Always Below 1 Ω
H93-25 (SNS2) - Body ground Always 10 kΩ or higher
H93-23 (MACC) - Body ground Always 10 kΩ or higher
H93-21 (MIN+) - Body ground Always 10 kΩ or higher
H93-22 (MIN-) - Body ground Always 10 kΩ or higher
H93-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E446276C05
1.5,0.75 1.917,1 0.417,0.25 2.813,2.604 2.052,2.156 true 2.271,2.896 1.927,2.156 true 1.198,2.833 1.813,2.146 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.604,0.792 1.917,0.99 0.313,0.198 10 false H93 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN- 2.083,2.896 2.583,3.115 0.5,0.219 10 false MACC 1.01,2.854 1.625,3.052 0.615,0.198 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H93-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-24 (SGND) - Body ground Always Below 1 Ω
H93-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

4.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E446247C01
1.5,0.219 1.938,0.49 0.438,0.271 1.052,0.271 1.188,0.271 1.188,0.271 1.292,1.094 true 0.865,0.51 1,0.51 1,0.51 1.219,1.104 true 1.594,0.26 1.906,0.458 0.313,0.198 10 false W7 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.854,3.438 3.167,3.635 0.313,0.198 10 false GND 0.625,0.177 1.094,0.385 0.469,0.208 10 false MCO+ 0.458,0.417 0.927,0.625 0.469,0.208 10 false MCO-
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with the connector(s) still connected.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Connect an oscilloscope to terminals 12 (MCO+) and 13 (MCO-) of the W7 map light assembly connector.


c.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal W7-12 (MCO+) - W7-13 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm (4.92 in.) from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT MAP LIGHT ASSEMBLY
5.INSPECT MAP LIGHT ASSEMBLY
a.
E355979C04
0.094,0.854 0.479,1.135 0.385,0.281 0.344,2.396 0.729,2.677 0.385,0.281 1.229,0.958 1.875,0.438 1.875,0.438 2.052,0.438 true 0.948,0.979 0.823,0.198 0.823,0.198 1,0.198 true 2.26,2.688 2.417,3.01 2.417,3.01 2.573,3.01 true 1.74,2.698 2.125,3.198 2.125,3.198 2.302,3.198 true 0.438,0.49 0.563,0.49 0.563,0.49 0.813,0.979 true 1.083,0.979 1.563,0.219 1.563,0.219 1.74,0.219 true 1.448,2.708 1.521,3.24 1.521,3.24 1.698,3.24 true 1.188,2.698 1,3.208 1,3.208 0.823,3.208 true 0.177,0.906 0.49,1.115 0.313,0.208 10 false W7 0.49,2.458 0.698,2.677 0.208,0.219 10 false B 2.615,2.927 3.052,3.135 0.438,0.208 10 false MACC 2.104,0.365 2.542,0.573 0.438,0.208 10 false MACC 1.813,0.146 2.292,0.365 0.479,0.219 10 false MCO+ 1.063,0.115 1.542,0.333 0.479,0.219 10 false MCO- 2.344,3.115 2.823,3.333 0.479,0.219 10 false MIC+ 1.76,3.156 2.24,3.375 0.479,0.219 10 false MIC- 0.042,0.417 0.521,0.635 0.479,0.219 10 false SNS2 0.427,3.135 0.906,3.354 0.479,0.219 10 false SNS2 0.063,0.083 0.542,0.302 0.479,0.219 10 false *a 0.042,1.531 0.521,1.75 0.479,0.219 10 false *b
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-11 (MACC) - B-5 (MACC) Always Below 1 Ω
W7-12 (MCO+) - B-3 (MIC+) Always Below 1 Ω
W7-13 (MCO-) - B-2 (MIC-) Always Below 1 Ω
W7-14 (SNS2) - B-1 (SNS2) Always Below 1 Ω
W7-11 (MACC) - W7-12 (MCO+) Always 10 kΩ or higher
W7-11 (MACC) - W7-13 (MCO-) Always 10 kΩ or higher
W7-11 (MACC) - W7-14 (SNS2) Always 10 kΩ or higher
W7-12 (MCO+) - W7-13 (MCO-) Always 10 kΩ or higher
W7-12 (MCO+) - W7-14 (SNS2) Always 10 kΩ or higher
W7-13 (MCO-) - W7-14 (SNS2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-25 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H93-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the G187 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-21 (MIN+) - G187-18 (MCO+) Always Below 1 Ω
H93-22 (MIN-) - G187-19 (MCO-) Always Below 1 Ω
H93-21 (MIN+) - Body ground Always 10 kΩ or higher
H93-22 (MIN-) - Body ground Always 10 kΩ or higher
H93-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)
a.

Disconnect the G187 DCM (telematics transceiver) connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-33 (MCVD) - W7-11 (MACC) Always Below 1 Ω
G187-34 (MCI+) - W7-12 (MCO+) Always Below 1 Ω
G187-35 (MCI-) - W7-13 (MCO-) Always Below 1 Ω
G187-33 (MCVD) - Body ground Always 10 kΩ or higher
G187-34 (MCI+) - Body ground Always 10 kΩ or higher
G187-35 (MCI-) - Body ground Always 10 kΩ or higher
G187-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the G187 DCM (telematics transceiver) connector.


E446276C02
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 true 2.813,2.604 2.052,2.156 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.583,0.781 1.896,0.979 0.313,0.198 10 false H95 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H95-24 (SGND) - Body ground Always Below 1 Ω
H95-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT DCM (TELEMATICS TRANSCEIVER)

NG

10.INSPECT DCM (TELEMATICS TRANSCEIVER)
a.

Connect the G187 DCM (telematics transceiver) connector.


b.
E283057C20
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.667,0.667 2.167,0.844 0.5,0.177 10 false G187
*a Component with harness connected
(DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G187-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-35 (MCI-) - Body ground Always Below 1 Ω
G187-32 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

11.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E446247C01
1.5,0.219 1.938,0.49 0.438,0.271 1.052,0.271 1.188,0.271 1.188,0.271 1.292,1.094 true 0.865,0.51 1,0.51 1,0.51 1.219,1.104 true 1.594,0.26 1.906,0.458 0.313,0.198 10 false W7 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.854,3.438 3.167,3.635 0.313,0.198 10 false GND 0.625,0.177 1.094,0.385 0.469,0.208 10 false MCO+ 0.458,0.417 0.927,0.625 0.469,0.208 10 false MCO-
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with the connector(s) still connected.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Connect an oscilloscope to terminals 12 (MCO+) and 13 (MCO-) of the W7 map light assembly connector.


c.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal W7-12 (MCO+) - W7-13 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm (4.92 in.) from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

12.CHECK DCM (TELEMATICS TRANSCEIVER) (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

5.INSPECT MAP LIGHT ASSEMBLY
12.CHECK DCM (TELEMATICS TRANSCEIVER) (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E364296C61
1.5,0.229 1.906,0.49 0.406,0.26 1.229,1.385 1.094,0.292 1.094,0.292 0.938,0.292 true 1.333,1.417 1.125,2.313 1.125,2.313 0.969,2.313 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.542,0.271 2,0.469 0.458,0.198 10 false G187 0.542,2.25 1.156,2.448 0.615,0.198 10 false MCO+ 0.5,0.229 1.115,0.427 0.615,0.198 10 false MCO- 2.823,3.458 3.24,3.656 0.417,0.198 10 false GND
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Connect an oscilloscope to terminal G187-18 (MCO+) and G187-19 (MCO-).


c.

Turn the ignition switch to ACC.


d.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G187-18 (MCO+) - G187-19 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ACC

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)