Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1324  Lost Communication with Meter  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter CAN reception error
·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E418182E23
0.896,2.427 5.479,2.625 4.583,0.198 10 false : Local Bus Communication Line 1.073,1.708 3.115,2.042 2.042,0.333 10 false Combination Meter Assembly 1.083,1.552 3.125,1.885 2.042,0.333 10 false G304 4.99,1.542 5.594,1.823 0.604,0.281 10 false H93 5.01,1.708 6.208,2.146 1.198,0.438 10 false Radio and Display Receiver Assembly 5.198,0.51 5.813,0.708 0.615,0.198 10 false CNH1 5.208,1.073 5.823,1.271 0.615,0.198 10 false CNL1 4.969,0.365 5.583,0.563 0.615,0.198 10 false 5 4.958,0.906 5.573,1.104 0.615,0.198 10 false 6 1.833,0.5 2.448,0.698 0.615,0.198 10 false MSCH 1.854,1.063 2.469,1.26 0.615,0.198 10 false MSCL 2.385,0.385 3,0.583 0.615,0.198 10 false 38 2.417,0.917 3.031,1.115 0.615,0.198 10 false 37

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-5 (CNH1) - G304-38 (MSCH) Always Below 1 Ω
H93-6 (CNL1) - G304-37 (MSCL) Always Below 1 Ω
H93-5 (CNH1) - Body ground Always 10 kΩ or higher
H93-6 (CNL1) - Body ground Always 10 kΩ or higher
H93-5 (CNH1) - H93-6 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H93-5 (CNH1) - Body ground Always Below 1 V
H93-6 (CNL1) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.
E317642C17
0.583,1.792 0.729,1.792 0.729,1.792 0.906,1.313 true 1.292,1.792 1.167,1.792 1.167,1.792 1.052,1.313 true 0.156,1.719 0.771,1.917 0.615,0.198 10 false MSCH 1.344,1.698 1.958,1.896 0.615,0.198 10 false MSCL 0.167,0.146 0.781,0.344 0.615,0.198 10 false *a
*a Component without harness connected
(Combination Meter Assembly)


Remove the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
38 (MSCH) - 37 (MSCL) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E408580C37
0.51,0.438 0.625,0.438 0.625,0.438 0.74,1.063 true 0.875,1.073 0.958,0.323 0.958,0.323 1.146,0.323 true 1.188,0.25 1.802,0.448 0.615,0.198 10 false CNH1 0.135,0.344 0.75,0.542 0.615,0.198 10 false CNL1 0.073,0.042 0.688,0.24 0.615,0.198 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (CNH1) - 6 (CNL1) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

4.CHECK COMBINATION METER ASSEMBLY

OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG