Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E446278E04
3.875,1.5 5.104,1.698 1.229,0.198 10 false RAD NO.2*2 4.188,2.063 5.417,2.26 1.229,0.198 10 false AMP*2 4.24,2.604 5.469,2.802 1.229,0.198 10 false ACC*2 1.74,2.469 2.969,2.667 1.229,0.198 10 false from ACC Relay*2 1.969,1.333 3.729,1.677 1.76,0.344 10 false from Battery*2 5.885,1.313 7.115,1.51 1.229,0.198 10 false +B 5.885,1.906 7.115,2.104 1.229,0.198 10 false +B2 5.885,2.51 7.115,2.708 1.229,0.198 10 false ACC 5.885,3.99 7.115,4.188 1.229,0.198 10 false GND 5.885,4.552 7.115,4.75 1.229,0.198 10 false GND2 5.885,3.083 6.344,3.281 0.458,0.198 10 false TX+ 5.896,3.635 6.354,3.833 0.458,0.198 10 false TX- 3.5,3.125 3.958,3.323 0.458,0.198 10 false TX1+ 3.531,3.688 3.99,3.885 0.458,0.198 10 false TX1- 2.813,4.271 4.031,4.677 1.219,0.406 10 false Radio and Display Receiver Assembly 0.948,5.281 3.344,5.625 2.396,0.344 10 false : AVC-LAN Communication Line 5.729,5 6.948,5.458 1.219,0.458 10 false Stereo Component Amplifier Assembly 5.604,3.865 6.833,4.063 1.229,0.198 10 false 3 5.563,4.417 6.792,4.615 1.229,0.198 10 false 18 5.552,2.24 6.781,2.438 1.229,0.198 10 false 12 5.594,1.115 6.823,1.313 1.229,0.198 10 false 1 5.552,1.677 6.781,1.875 1.229,0.198 10 false 16 5.604,3.427 6.833,3.625 1.229,0.198 10 false 7 5.615,2.875 6.844,3.073 1.229,0.198 10 false 8 3.917,2.979 5.146,3.177 1.229,0.198 10 false 5 3.917,3.542 5.146,3.74 1.229,0.198 10 false 6 1.313,0.458 2.729,0.865 1.417,0.406 10 false from Eco Run Vehicle Converter Assembly*1 0.302,4.563 2.281,4.833 1.979,0.271 10 false *1: w/ Stop and Start System 0.313,4.885 2.521,5.198 2.208,0.313 10 false *2: w/o Stop and Start System 5.521,1.333 6.75,1.531 1.229,0.198 10 false H67 5.51,1.896 6.74,2.094 1.229,0.198 10 false H67 5.458,2.458 6.688,2.656 1.229,0.198 10 false H105 5.469,3.104 6.698,3.302 1.229,0.198 10 false H105 5.469,3.667 6.698,3.865 1.229,0.198 10 false H105 5.5,4.094 6.729,4.292 1.229,0.198 10 false H67 5.521,4.656 6.75,4.854 1.229,0.198 10 false H67 2.792,4.073 4.01,4.479 1.219,0.406 10 false H92 3.729,0.302 4.958,0.5 1.229,0.198 10 false RAD NO.4*1 3.667,0.688 4.896,0.885 1.229,0.198 10 false AMP NO.2*1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC

OK

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.
E382108C14
1.573,0.208 1.958,0.438 0.385,0.229 1.542,1.729 1.896,1.979 0.354,0.25 0.49,0.417 0.625,0.417 0.625,0.417 0.573,0.865 true 0.458,1.531 0.594,1.531 0.594,1.531 0.573,1.042 true 0.781,1.781 0.917,1.781 0.917,1.781 0.865,1.042 true 2.708,2.104 2.594,2.104 2.594,2.104 2.396,2.583 true 0.906,0.229 1.042,0.229 1.042,0.229 0.875,0.875 true 0.125,0.094 0.302,0.26 0.177,0.167 10 false *a 1.625,0.25 1.927,0.417 0.302,0.167 10 false H67 1.552,1.771 2.125,1.99 0.573,0.219 10 false H105 0.563,0.135 0.927,0.302 0.365,0.167 10 false GND 0.177,1.458 0.5,1.625 0.323,0.167 10 false +B2 0.365,1.708 0.781,1.875 0.417,0.167 10 false GND2 2.75,2.031 3.104,2.198 0.354,0.167 10 false ACC 0.25,0.323 0.573,0.49 0.323,0.167 10 false +B
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-3 (GND) - Body ground Always Below 1 Ω
H67-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/ Stop and Start System

*2: w/o Stop and Start System

H67-1 (+B) - H67-3 (GND) Always 10.5 to 16 V*1
11 to 14 V*2
H67-16 (+B2) - H67-3 (GND) Always 10.5 to 16 V*1
11 to 14 V*2
H105-12 (ACC) - H67-3 (GND) Ignition switch ACC 10.5 to 16 V*1
11 to 14 V*2


Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H92 radio and display receiver assembly connector.


b.

Disconnect the H105 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H92-5 (TX1+) - H105-8 (TX+) Always Below 1 Ω
H92-6 (TX1-) - H105-7 (TX-) Always Below 1 Ω
H92-5 (TX1+) - Body ground Always 10 kΩ or higher
H92-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL



c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG