Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0329245 ROAD SIGN ASSIST SYSTEM Y

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Before performing troubleshooting for the road sign assist system, make sure that the pre-collision system and lane departure alert system are not malfunctioning.

Pre-collision system: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Lane departure alert system: Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Perform the following procedure to troubleshoot the road sign assist system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check in CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTCs*

NG

5.CHECK FOR DTCs*
a.

Check for DTCs.


b.

Make a note of any DTCs that are output.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK VEHICLE CONTROL HISTORY*

B

7.RECONFIRM DTC OUTPUT*
6.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear for vehicle control history.


b.

Using the GTS, check for vehicle control history.


Result:
Result Proceed to
Vehicle control history codes are not output A
Vehicle control history codes are output B



A

B

8.RECONFIRM VEHICLE CONTROL HISTORY*
7.RECONFIRM DTC OUTPUT*
a.

Clear the DTCs.


b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Recheck for DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK VEHICLE CONTROL HISTORY*

B

8.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the vehicle control history.


b.

Using the GTS, check for vehicle control history.


Result:
Result Proceed to
Vehicle control history codes are not output A
Vehicle control history codes are output B



A

B