Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438241 FRONT CAMERA SYSTEM Y

CRUISE CONTROL  FRONT CAMERA SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Before performing troubleshooting for the front camera system, perform troubleshooting for the pre-collision system.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a pre-collision system related warning message is displayed on the multi-information display, refer to How to Proceed with Troubleshooting for Pre-collision System.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Use the following procedure to troubleshoot the front camera system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:

If the battery voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



b.

While using the parts location and circuit diagrams as a reference, inspect areas which can be visually inspected for blown fuses, problems with wire harnesses (open and short circuits), improperly connected connectors, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Using the GTS, check for DTCs.


b.

If a DTC is output, record the DTC.


Result:
Result Proceed to
DTCs are not output A
DTC C1AA800 is output B
DTC other than C1AA800 is output C



A

7.CHECK VEHICLE CONTROL HISTORY*

B

GO TO DIAGNOSTIC TROUBLE CODE CHART (C1AA8000)

C

6.RECONFIRM DTC OUTPUT*
6.RECONFIRM DTC OUTPUT*
a.

Using the GTS, clear the DTCs.


b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Using the GTS, check for DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.CHECK VEHICLE CONTROL HISTORY*

B

7.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for Vehicle Control History (RoB).


b.

Make a note of the output Vehicle Control History (RoB).


Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) other than X2015 and X201C is output B
Vehicle Control History (RoB) X2015 or X201C is output C



A

B

8.RECONFIRM VEHICLE CONTROL HISTORY*

C

GO TO VEHICLE CONTROL HISTORY (X2015 or X201C)

8.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the Vehicle Control History (RoB).


b.

Using the GTS, check for Vehicle Control History (RoB).


Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) is output B



A

B