Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438241 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1AA800  Front Recognition Camera Optical Axis Misalignment Malfunction  


DESCRIPTION

The forward recognition camera monitors its optical axis status. If it determines that the optical axis alignment has become misaligned, it will output DTC C1AA800.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA800 Front Recognition Camera Optical Axis Misalignment Malfunction When the forward recognition camera detects an optical axis misalignment when the vehicle is being driven at a speed of 5 km/h (4 mph) or more, after 3 seconds have elapsed since the ignition switch was turned to ON.
·

Windshield glass

·

Vehicle operating conditions

·

Wheel alignment

·

Forward recognition camera assembly beam axis adjustment



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the forward recognition camera may not operate properly due to a difference in the transmissivity or black ceramic border.

·

Forward recognition camera optical axis may deviate if the vehicle is driven on a banked road, such as a racetrack. This deviation can be corrected by driving the vehicle on a normal road for a while.

·

Forward recognition camera optical axis may deviate when the vehicle is overloaded or the wheel alignment (toe-in) is incorrect. The forward recognition camera optical axis can be corrected by decreasing the load on the vehicle or adjusting the toe-in.



PROCEDURE

1.CHECK FORWARD RECOGNITION CAMERA INSTALLATION

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION

HINT:

If there is deformation or deviation in the forward recognition camera installation bracket, replace the windshield glass.


OK:

No deformation or deviation in forward recognition camera installation bracket.


Result:
Proceed to
OK
NG



OK

2.CHECK VEHICLE OPERATING CONDITION

NG

11.REPLACE WINDSHIELD GLASS
2.CHECK VEHICLE OPERATING CONDITION
HINT:

Check if a condition which caused the forward recognition camera optical axis to become temporarily misaligned existed, such as if the vehicle was overloaded, towed or modified.


OK:

Vehicle was not overloaded, towed or modified.


Result:
Proceed to
OK
NG



OK

3.CHECK WHEEL ALIGNMENT (TOE)

NG

9.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
3.CHECK WHEEL ALIGNMENT (TOE)

Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

OK:

Front wheels are not misaligned (toe)


Result:
Proceed to
OK
NG



OK

4.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT

NG

6.ADJUST WHEEL ALIGNMENT (TOE)
4.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.


Result:
Proceed to
NEXT



NEXT

END

6.ADJUST WHEEL ALIGNMENT (TOE)

NEXT

7.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
7.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.


Result:
Proceed to
NEXT



NEXT

END

9.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
a.

Return the vehicle to normal operating conditions.


b.

Perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.


Result:
Proceed to
NEXT



NEXT

END

11.REPLACE WINDSHIELD GLASS

NEXT

12.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
12.PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT
HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.


Result:
Proceed to
NEXT



NEXT

END