Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2020.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261239 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane departure alert system, road sign assist system, pre-collision system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53828J 4.REMOVE FRONT FENDER SIDE PANEL PROTECTOR LH

Hide 53827K 5.REMOVE FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:

Use the same procedure for the LH side.


Hide 53867H 6.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 7.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure for the LH side.


Hide 85192 8.REMOVE WINDSHIELD WIPER ARM COVER

Hide 9.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 10.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55781E 11.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 75536B 12.REMOVE WINDSHIELD LOWER OUTSIDE MOULDING LH

a.
B241712C02
2.125,0.844 2.458,0.844 true 2.479,0.74 2.792,0.938 0.313,0.198 10 false *a
*a Protective Tape


Remove the windshield lower outside moulding.

i.

Put protective tape around the moulding.


ii.

Using a moulding remover, detach the 5 clips and remove the moulding.

NOTICE:
·

When removing the windshield lower outside moulding, be careful not to damage the No. 1 windshield outside moulding clip.

·

If a No. 1 windshield outside moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.





Hide 75535A 13.REMOVE WINDSHIELD LOWER OUTSIDE MOULDING RH

HINT:

Use the same procedure described for the LH side.


Hide 67920 14.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

Hide 67910 15.REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 16.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 17.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 18.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 19.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74616C 20.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

Hide 74615E 21.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 23.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 24.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 74318 25.REMOVE VISOR BRACKET COVER LH

Hide 74317 26.REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 74310 28.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 81260A 30.REMOVE MAP LIGHT ASSEMBLY

Hide 86466E 31.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 86466D 32.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 86464A 33.REMOVE FORWARD RECOGNITION LATCH (w/ Lane Departure Alert System)

Hide 8646C 34.REMOVE FORWARD RECOGNITION CAMERA (w/ Lane Departure Alert System)

Hide 86401 35.REMOVE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Lane Departure Alert System)

Hide 89941 36.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 87810 37.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 63310 38.REMOVE ROOF HEADLINING ASSEMBLY

a.

for 5 Door:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining assembly. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed in a later step.

Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL




b.

for 3 Door:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining assembly. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed in a later step.

Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL




Hide 56111 39.REMOVE WINDSHIELD GLASS

NOTICE:
·

There are No. 1 and No. 2 windshield glass stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle specifications, a 1-piece or 2-piece type stopper is used.


B238992C04
1.646,0.927 1.427,0.865 false 5.177,0.792 4.99,0.792 false 5.458,0.677 5.625,0.927 5.625,0.927 5.729,0.927 false 0.677,0.115 0.99,0.521 0.313,0.406 12 false *A 4.24,0.104 4.594,0.479 0.354,0.375 12 false *B 1.26,0.771 1.49,0.99 0.229,0.219 10 false *1 4.833,0.719 5.063,0.938 0.229,0.219 10 false *1 5.76,0.854 5.99,1.073 0.229,0.219 10 false *2
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


a.

w/ Windshield Deicer System:

Disconnect the windshield deicer connector.


b.
B238993C03
1.271,0.542 0.688,0.292 false 0.448,0.208 0.667,0.417 0.219,0.208 10 false *a
*a Protective Tape


Apply protective tape to the outer surface of the vehicle body to prevent scratches.


c.
B238994C02
1.26,3.271 0.948,3.271 false 1.271,2.917 1.271,2.427 1.271,2.427 2.5,2.427 false 2.26,2.906 2.26,2.427 false 2.448,1.073 2.865,1.281 2.865,1.281 2.865,1.417 false 0.49,1.583 0.49,1.208 0.49,1.208 0.333,1.208 false 1.677,0.75 1.49,0.219 1.49,0.219 1.375,0.219 false 1.25,0.781 1.031,0.365 1.031,0.365 0.927,0.365 false 0.75,0.281 1.021,0.49 0.271,0.208 10 false *a 1.188,0.146 1.427,0.396 0.24,0.25 10 false *b 0.146,1.073 0.375,1.271 0.229,0.198 10 false *c 2.75,1.469 2.958,1.646 0.208,0.177 10 false *d 2.552,2.365 2.75,2.542 0.198,0.177 10 false *1 1.281,3.177 1.51,3.375 0.229,0.198 10 false *b
*1 Windshield Glass Stopper
*a Plastic Sheet
*b Piano Wire
*c Wooden Blocks
*d Protective Tape


From the interior, insert a piano wire between the vehicle body and windshield glass as shown in the illustration.


d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the windshield glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and instrument panel.




e.
B238990C01
1.646,0.927 1.417,0.927 1.417,0.927 1.417,1.885 false 1.333,1.917 1.594,2.146 0.26,0.229 10 false *a
*a Matchmarks


Place matchmarks over the windshield glass and vehicle body at the locations indicated in the illustration.

NOTICE:

Matchmarks do not need to be placed if not reusing the windshield glass.



f.

Cut through the adhesive by pulling the piano wire around the windshield glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the windshield glass.



g.

Disconnect the stoppers.


h.
B238991

Using suction cups, remove the windshield glass.


Hide 56117D 40.REMOVE WINDSHIELD GLASS ADHESIVE DAM

a.

Using a scraper, remove the windshield glass adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield glass adhesive dam with a new one.




Hide 75533G 41.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

Using a scraper, remove the windshield outside moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.




Hide 56116C 42.REMOVE NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.




Hide 56115A 43.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B238995

Remove the 2 No. 1 windshield glass stoppers.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 75545B 44.REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

B241713

a.

Remove the 5 No. 1 windshield moulding clips.

HINT:

Use the same procedure to remove the 5 No. 1 windshield moulding clips on the other side.



Hide 75547B 45.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clips.


a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.
B598543N01
1.563,1.698 1.99,1.896 0.427,0.198 10 false a

Lightly press the drill against the No. 3 windshield outside moulding clips, drill off the flanges of the 5 No. 3 windshield outside moulding clips, and remove it.

CAUTION:

Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Do not pry the No. 3 windshield outside moulding clips with the drill because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.



Standard Dimension:
Area Dimension
a 5 mm (0.197 in.)



d.

Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

HINT:

Use the same procedure to remove No. 3 windshield outside moulding clips on the other side.



Hide 56111 46.CLEAN WINDSHIELD GLASS

B106929

a.

Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.


b.

Clean the outer circumference of the glass with non-residue solvent.

NOTICE:
·

Do not touch the surface of the glass after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 47.CLEAN VEHICLE BODY

B106081C54
0.51,1.292 0.115,0.115 0.115,0.115 0.26,0.115 false 2.302,1.427 1.594,0.156 1.594,0.156 1.844,0.156 false 2.656,1.542 2.5,1.906 2.5,1.906 0.667,1.646 false 0.323,0.031 0.635,0.26 0.313,0.229 10 false *a 1.906,0.073 2.542,0.25 0.635,0.177 10 false *a 2.604,1.896 2.917,2.094 0.313,0.198 10 false *b
*a Adhesive
*b Vehicle Body


a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.