Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for i-ART) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438249 CRUISE CONTROL SYSTEM(for i-ART) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for i-ART)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. When the ECM receives the signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal operation even if there is a malfunction in the stop light switch signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the cruise control system is operating, the voltage of the STP and ST1- terminals of the ECM are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

C448905E03
2.438,2.219 4.354,2.469 1.917,0.25 10 false Stop Light Switch Assembly 2.844,3.49 4.448,4.24 1.604,0.75 10 false Skid Control ECU (Master Cylinder Solenoid) 4.688,4.823 7.01,5.417 2.323,0.594 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly) 5.427,3.604 6.938,4.167 1.51,0.563 10 false Certification ECU (Smart Key ECU Assembly)*2 4.021,2.969 4.563,3.208 0.542,0.24 10 false 45 2.844,3.302 3.385,3.542 0.542,0.24 10 false A7 0.5,0.594 1.51,0.792 1.01,0.198 10 false from Battery 0.344,1.396 1.833,1.74 1.49,0.344 10 false from IG2 Relay 6.052,2.281 6.594,2.521 0.542,0.24 10 false ECM 3.979,0.479 4.229,0.719 0.25,0.24 10 false 3 5.688,0.74 6.229,0.979 0.542,0.24 10 false STP 5.708,1.531 6.25,1.771 0.542,0.24 10 false ST1- 6.042,2.104 6.865,2.385 0.823,0.281 10 false G185 3.979,1.25 4.229,1.49 0.25,0.24 10 false 5 5.385,0.5 5.792,0.771 0.406,0.271 10 false 13 5.396,1.281 5.792,1.604 0.396,0.323 10 false 12 1.938,0.781 2.948,0.979 1.01,0.198 10 false STOP 1.99,1.563 2.344,1.771 0.354,0.208 10 false IGN 2.427,2.042 2.813,2.271 0.385,0.229 10 false A99 2.604,1.281 2.854,1.521 0.25,0.24 10 false 6 3.979,1.573 4.229,1.813 0.25,0.24 10 false 2 4.677,4.646 5.729,4.844 1.052,0.198 10 false G150*1, G45*2 5.76,3.063 6.302,3.302 0.542,0.24 10 false STP1 5.75,4.406 6.292,4.646 0.542,0.24 10 false STP 5.135,4.302 6.104,4.583 0.969,0.281 10 false 4*1, 6*2 5.427,3.427 5.969,3.667 0.542,0.24 10 false G213 5.563,2.948 6.104,3.188 0.542,0.24 10 false 2 3.563,3.073 4.104,3.354 0.542,0.281 10 false STP2 3.583,1.573 4.042,1.771 0.458,0.198 10 false GND 2.573,0.5 2.823,0.74 0.25,0.24 10 false 7 2.792,0.49 3.042,0.729 0.25,0.24 10 false B 3.781,1.26 4.031,1.5 0.25,0.24 10 false L 2.792,1.271 3.042,1.51 0.25,0.24 10 false B 3.792,0.49 4.042,0.729 0.25,0.24 10 false L 3.281,1.104 3.594,1.302 0.313,0.198 10 false IC 0.333,4.865 3.219,5.25 2.885,0.385 10 false *1: w/o Entry and Start System 0.323,5.292 3.208,5.677 2.885,0.385 10 false *2: w/ Entry and Start System 5.115,2.938 5.427,3.135 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to the Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
A395526C44
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.563,0.313 2.021,0.51 0.458,0.198 10 false A99
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-6 (B) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A99-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

*1: w/o Entry and Start System

*2: w/ Entry and Start System


a.

Disconnect the G185 ECM connector.


b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.*2


d.

Disconnect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G185-12 (ST1-) - A99-5 (L) Always Below 1 Ω
G185-13 (STP) - A99-3 (L) Always Below 1 Ω
G185-12 (ST1-) or A99-5 (L) - Body ground Always 10 kΩ or higher
G185-13 (STP) or A99-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR