The radio and display receiver assembly and television display assembly are connected by the AVC-LAN communication line.
This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and television display assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15D5 | Rear Seat Entertainment System Disconnected | When either condition below is met:
·
The television display assembly is/was not connected while the ignition switch is/was ON or ACC ·
Communication between the master unit and the television display assembly is not possible when the engine is started |
·
Television display assembly power source circuit ·
AVC-LAN circuit between radio and display receiver assembly and television display assembly ·
Television display assembly ·
Radio and display receiver assembly ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Television Display Assembly) |
Disconnect the television display assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W14-17 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||
| W14-1 (+B) - W14-17 (GND) | Always | 11 to 14 V*1
10.5 to 16 V*2 |
| W14-2 (ACC) - W14-17 (GND) | Ingition switch ACC | 11 to 14 V*1
10.5 to 16 V*2 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H92 radio and display receiver assembly connector.
Disconnect the W14 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W14-4 (TX1+) - H92-19 (TX+) | Always | Below 1 Ω |
| W14-5 (TX1-) - H92-20 (TX-) | Always | Below 1 Ω |
| W14-4 (TX1+) - Body ground | Always | 10 kΩ or higher |
| W14-5 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the television display assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL