Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260654 INTAKE MANIFOLD A

1GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the supply pump assembly removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53737A 3.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

Hide 25800 4.REMOVE EGR COOLER ASSEMBLY (w/ EGR Cooler)

Hide 25800 5.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 6.DRAIN ENGINE COOLANT (w/o EGR System)

Hide 26100G 7.REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

Hide 87209 8.DISCONNECT WATER HOSE SUB-ASSEMBLY (w/o EGR System)

a.
A473875

Slide the 2 clamps and disconnect the water hose sub-assembly from the No. 2 water by-pass pipe.


Hide 16278 9.REMOVE NO. 2 WATER BY-PASS PIPE (w/o EGR System)

a.
A473874C01
0.281,1.104 0.646,1.281 0.365,0.177 10 true *1,*2 0.073,0.323 0.313,0.49 0.24,0.167 10 true *3 2.271,1.729 2.448,1.896 0.177,0.167 10 true *4
*1 Water Hose Sub-assembly
*2 No. 13 Water By-pass Hose
*3 No. 15 Water By-pass Hose
*4 No. 16 Water By-pass Hose


w/ Viscous Heater:

Slide the clamp and disconnect the water hose sub-assembly from the No. 2 water by-pass pipe.


b.

w/o Viscous Heater:

Slide the clamp and disconnect the No. 13 water by-pass hose from the No. 2 water by-pass pipe.


c.

Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.


d.

Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR cooler.


e.

Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly, No. 3 water by-pass pipe sub-assembly and No. 2 engine cover bracket.


Hide 23265C 10.REMOVE GAS FILTER (w/o EGR System)

a.
A369950

Disconnect the 2 vacuum hoses from the turbo pressure sensor and intake manifold.


b.

Remove the gas filter from the gas filter bracket.


Hide 89421C 11.REMOVE TURBO PRESSURE SENSOR (w/o EGR System)

a.
A369951

Disconnect the connector from the turbo pressure sensor.


b.

Remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.


Hide 12633 12.REMOVE NO. 3 ENGINE COVER BRACKET (w/o EGR System)

a.
A339756

Remove the 2 bolts and No. 3 engine cover bracket from the engine cover bracket and No. 2 engine cover bracket.


Hide 12632 13.REMOVE NO. 2 ENGINE COVER BRACKET (w/o EGR System)

a.
A352125

Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly.


Hide 44306 14.DISCONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY (w/o EGR System)

a.
A417203

Remove the 2 bolts and disconnect the vane pump oil reservoir sub-assembly from the body.


Hide 82121 15.DISCONNECT ENGINE WIRE (w/o EGR System)

a.
A473862

Detach the 2 clamps and disconnect the 2 connectors from the turbocharger sub-assembly.


b.
A473863

Disconnect the connector from the camshaft position sensor.


c.

Disconnect the 4 connectors from the 4 injector assemblies.


d.

Disconnect the connector from the glow plug connector.


e.

Disconnect the connector from the sensor wire of common rail assembly.


f.

Remove the 3 bolts and detach the 2 clamps.


g.
A473864

Disconnect the 3 connectors.


h.

Remove the bolt and detach the 3 clamps.


Hide 25624 16.REMOVE EGR VALVE ADAPTER (w/o EGR Cooler)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A368227

Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


b.
A368228

w/ EGR System:

i.

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


ii.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the EGR valve adapter.



c.
A408313

w/o EGR System:

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the EGR valve adapter.


d.
A368229

w/ EGR System:

i.

Slide the clamp and disconnect the No. 7 water by-pass hose from the EGR pipe stay.


ii.

Slide the clamp and disconnect the water hose from the EGR valve adapter.


iii.

Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.



e.
A408314

w/o EGR System:

i.

Slide the clamp and disconnect the No. 7 water by-pass hose from the EGR pipe stay.


ii.

Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.



f.
A473865

w/ EGR System:

Remove the 2 nuts and disconnect the No. 1 EGRpipe sub-assembly from the EGR valve adapter.


g.

Remove the 4 bolts and EGR valve adapter from the intake manifold.

A408315C02
0.042,0.083 0.302,0.281 0.26,0.198 10 true *A 3.823,0.083 4.104,0.302 0.281,0.219 10 true *B
*A w/ EGR System *B w/o EGR System



h.
A412880

Remove the 2 bolts and EGR pipe stay from the EGR valve adapter.


Hide 11409 17.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A418177

w/ No. 2 Fuel Pipe Clamp:

Detach the No. 2 fuel pipe clamp from the engine oil level dipstick guide.


b.

Remove the engine oil level dipstick.


c.

Disconnect the vacuum hose from the intake manifold.


d.

Remove the bolt and engine oil level dipstick guide.


e.

Remove the O-ring and grommet from the engine oil level dipstick guide.


Hide 23812D 18.DISCONNECT NO. 2 FUEL PIPE

A352807

a.

Remove the bolt and disconnect the No. 2 fuel pipe.


Hide 19.REMOVE WIRING HARNESS CLAMP BRACKET

A352808

a.

Disconnect the diesel throttle body assembly connector and pre-stroke control valve connector.


b.
A353379

Detach the 2 wire harness clamps.


c.

Remove the bolt and wiring harness clamp bracket.


Hide 17118 20.REMOVE MANIFOLD STAY

A353380

a.

Remove the bolt and disconnect the wiring harness clamp bracket from the intake manifold stay.


b.
A454364

Remove the 2 bolts and manifold stay.


Hide 23804D 21.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

a.
A356214C07
0,0 0,0 false
V100136

Union Bolt
V100137

Bolt


Disconnect the No. 4 fuel pipe sub-assembly from the No. 1 fuel pipe.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Remove the bolt from the intake manifold.


c.

Remove the 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.


Hide 23815D 22.REMOVE NO. 3 FUEL PIPE

a.
A454519

Detach the clamp and disconnect the wire harness.


b.
A352782C03
0,0 0,0 false
V100135

Union Bolt
V100136

Supply Pump Hollow Screw


Remove the union bolts, supply pump hollow screw and 2 gaskets from the supply pump assembly and fuel filter.


c.

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter.


Hide 23804C 23.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

U169511C01
0.083,0 0.354,0.208 0.271,0.208 10 false *a 0.323,2.448 0.594,2.656 0.271,0.208 10 false *b
*a Common Rail Assembly Side
*b Fuel Supply Pump Assembly Side


a.

Remove the 2 bolts, No. 1 injection pipe clamp and No. 2 injection pipe clamp.


b.
U169505E01
0.541,1.054 0.983,1.242 0.441,0.188 10 SST 0.88,1.155 1.193,1.155 false 1.193,1.155 1.502,1.668 false

Using SST, loosen the fuel inlet pipe sub-assembly union nut of the common rail assembly side.

SST
09245-11010  

NOTICE:

If the No. 1 or No. 2 injection pipe clamp is removed from the inlet pipe sub-assembly, replace the No. 1 or No. 2 injection clamp with a new one.



c.

Using a 19 mm union nut wrench, loosen the inlet pipe sub-assembly union nut of the fuel supply pump assembly side.


Hide 23770 24.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

A345101

a.

Slide the 2 clamps and remove the No. 4 fuel hose from the No. 2 nozzle leakage pipe assembly and common rail assembly.


b.

Slide the 2 clamps and remove the No. 5 fuel hose from the No. 1 nozzle leakage pipe assembly and No. 2 nozzle leakage pipe assembly.


c.
A345102

Slide the clamp and disconnect the No. 6 fuel hose from the No. 3 nozzle leakage pipe assembly.


d.

Remove the 2 bolts and No. 2 nozzle leakage pipe assembly.


Hide 17111 25.REMOVE INTAKE MANIFOLD

a.
A356217E01
2.406,0.583 2.625,0.583 2.625,0.583 2.917,0.792 true 1.208,1.917 1.385,1.917 1.385,1.917 1.583,1.698 true 2.25,1.823 2.427,1.823 2.427,1.823 2.625,1.604 true 1.094,1.823 1.292,2.042 0.198,0.219 10 true A 2.146,1.719 2.344,1.938 0.198,0.219 10 true B 2.292,0.49 2.49,0.708 0.198,0.219 10 true C

Remove the 3 bolts and disconnect the wire harness bracket A, B and C.


b.
A345105C07
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 7 bolts, 2 nuts, intake manifold and gasket.