1.DRAIN ENGINE COOLANT
2.DRAIN ENGINE COOLANT (w/ Urea SCR System)
17940D
3.REMOVE INTERCOOLER ASSEMBLY (w/ Urea SCR System)
55781E
4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
26100G
5.REMOVE DIESEL THROTTLE BODY ASSEMBLY
87209
6.REMOVE WATER HOSE SUB-ASSEMBLY
w/ Rear Air Conditioning System:
Slide the 2 clamps and disconnect the 2 water hoses from the water pipe.
Slide the 2 clamps and remove the 2 water hoses from the air conditioning unit assembly.
w/o Rear Air Conditioning System:
Slide the 2 clamps and remove the 2 water hoses from the air conditioning unit assembly.
16278
7.REMOVE NO. 2 WATER BY-PASS PIPE
w/o Urea SCR System:
w/ EGR Pre-cooler:
Slide the clamp and disconnect the No. 18 water by-pass hose from the No. 1 EGR pipe sub-assembly.
w/ EGR Pre-cooler:
Detach the clamp and disconnect the No. 18 water by-pass hose from the No. 2 engine cover bracket.
w/ Viscous Heater:
Slide the clamp and disconnect the water by-pass hose sub-assembly from the No. 2 water by-pass pipe.
w/o Viscous Heater:
Slide the clamp and disconnect the No. 13 water by-pass hose from the No. 2 water by-pass pipe.
Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.
w/ EGR Cooler:
Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR cooler.
w/o EGR Cooler:
Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR pipe stay.
Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly, No. 3 water by-pass pipe sub-assembly and No. 2 engine cover bracket.
23265C
8.REMOVE GAS FILTER
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
w/ Clip:
Slide the clip and disconnect the vacuum hose from the turbo pressure sensor.
w/o Clip:
Disconnect the vacuum hose from the turbo pressure sensor.
Disconnect the vacuum hose from the intake manifold.
Remove the gas filter from the gas filter bracket.
89421C
9.REMOVE DIESEL TURBO PRESSURE SENSOR
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Disconnect the connector from the turbo pressure sensor.
Remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.
12633
10.REMOVE NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)
Remove the 2 bolts and No. 3 engine cover bracket from the engine cover bracket and No. 2 engine cover bracket.
12632
11.REMOVE NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)
Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly.
77820
12.DISCONNECT UREA TANK FILLER PIPE ASSEMBLY (w/ Urea SCR System)
Remove the 3 bolts and disconnect the urea tank filler pipe assembly from the No. 1 oil reservoir bracket assembly.
44306
13.DISCONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY
Remove the 2 bolts and disconnect the vane pump oil reservoir sub-assembly from the body.
82121
14.DISCONNECT ENGINE WIRE
w/o Urea SCR System:
Detach the 2 clamps and disconnect the 2 connectors from the turbocharger sub-assembly.
| *A | w/ DPF |
w/ DPF:
Detach the clamp and disconnect the connector from the differential pressure sensor.
w/ DPF:
Disconnect the 3 connectors from the exhaust gas temperature sensors.
w/ DPF:
Disconnect the connector from the exhaust fuel addition injector assembly.
Disconnect the connector from the camshaft position sensor.
Disconnect the 4 connectors from the 4 injector assemblies.
Disconnect the connector from the electric EGR control valve assembly.
Disconnect the connector from the glow plug connector.
Disconnect the connector from the sensor wire of common rail assembly.
Detach the clamp and remove the bolt.
Detach the clamp and disconnect the 2 connectors from the vane pump assembly.
Detach the clamp and remove the bolt.
Disconnect the connector from the vacuum control valve set.
w/ Urea SCR System:
Detach the 3 clamps and disconnect the 2 connectors from the turbocharger sub-assembly.
Disconnect the camshaft position sensor.
Disconnect the connector from the exhaust fuel addition injector assembly.
Remove the bolt and disconnect the engine wire from the engine cover bracket.
Disconnect the connector from the differential pressure sensor.
Disconnect the 3 connectors from the 3 exhaust gas temperature sensors.
Detach the clamp and remove the bolt.
Disconnect the connector from the No. 1 nitrogen oxides sensor.
Disconnect the 4 connectors from the 4 injector assemblies.
Disconnect the connector from the sensor wire of common rail assembly.
Disconnect the connector from the glow plug connector.
Disconnect the electric EGR control valve assembly.
Detach the clamp and remove the 3 bolts.
Disconnect the 2 connectors from the vane pump assembly.
Disconnect the connector from the engine water temperature sensor.
Detach the clamp and remove the bolt.
Detach the clamp and disconnect the connector from the vacuum control valve set.
Detach the clamp and remove the bolt, and disconnect the engine wire.
25625
15.REMOVE EGR VALVE BRACKET
Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.
25612
16.REMOVE NO. 2 EGR PIPE
Detach the 6 clamps and disconnect the engine room main wire.
Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.
Remove the 2 gaskets.
25800
17.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.
Remove the 2 bolts and electric EGR control valve assembly.
Remove the gasket.
16206B
18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.
Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.
16209
19.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)
Slide the 2 clamps and remove the No. 17 water by-pass hose from the No. 1 EGR pipe sub-assembly and No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 1 EGR cooler.
Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.
Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.
25601
20.DISCONNECT NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR Cooler)
Remove the 2 nuts and disconnect the No. 1 EGR pipe sub-assembly from the EGR valve adapter.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the No. 2 EGR valve assembly.
25804
21.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)
22.REMOVE NO. 1 EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)
w/o Urea SCR System:
Remove the 4 bolts and No. 1 EGR cooler with No. 2 EGR valve assembly from the intake manifold.
w/ Urea SCR System:
Remove the 4 bolts, No. 2 intercooler support bracket and No. 1 EGR cooler with No. 2 EGR valve assembly from the intake manifold.
Remove the gasket.
25624
23.REMOVE EGR VALVE ADAPTER (w/ EGR Cooler)
Remove the 2 bolts and EGR valve adapter from the No. 2 EGR valve assembly.
Remove the gasket.
25630
24.REMOVE NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Remove the 4 bolts and No. 2 EGR valve assembly from the No. 1 EGR cooler.
Remove the gasket.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the No. 2 EGR valve assembly.