Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2020.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2311  Power Window Motor Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies.

The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is output when a power window regulator motor assembly is malfunctioning, or the ECU built into the power window regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

D-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is malfunctioning

(b)

When ECU in front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position



·

Front power window regulator motor assembly RH (for RHD)

·

Front power window regulator motor assembly LH (for LHD)

·

Incorrect installation of power window components

·

Overheated front power window regulator motor assembly LH (for LHD)

·

Overheated front power window regulator motor assembly RH (for RHD)

·

Harness or connector



P-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) is malfunctioning

(b)

When ECU in front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position



·

Front power window regulator motor assembly RH (for LHD)

·

Front power window regulator motor assembly LH (for RHD)

·

Incorrect installation of power window components

·

Overheated front power window regulator motor assembly RH (for LHD)

·

Overheated front power window regulator motor assembly LH (for RHD)

·

Harness or connector



RL-Door Motor (for 5 Door)
DTC Code DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Rear power window regulator motor assembly LH is malfunctioning

(b)

When ECU in rear power window regulator motor assembly LH determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position



·

Rear power window regulator motor assembly LH

·

Incorrect installation of power window components

·

Overheated rear power window regulator motor assembly LH

·

Harness or connector



RR-Door Motor (for 5 Door)
DTC Code DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Rear power window regulator motor assembly RH is malfunctioning

(b)

When ECU in rear power window regulator motor assembly RH determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position



·

Rear power window regulator motor assembly RH

·

Incorrect installation of power window components

·

Overheated rear power window regulator motor assembly RH

·

Harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 is stored in each power window regulator motor assembly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check the parts which the DTCs have been output from.

Result
Result Proceed to
DTC output from D-Door Motor (for LHD) A
DTC output from D-Door Motor (for RHD) B
DTC output from P-Door Motor (for LHD) B
DTC output from P-Door Motor (for RHD) A
DTC output from RL-Door Motor (for 5 Door) C
DTC output from RR-Door Motor (for 5 Door) D



A

3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

B

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)

C

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

D

18.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
U169636E02
1.854,1.125 2.438,1.323 false 1.563,1.115 0.958,1.313 false 1.615,0.385 1.896,0.573 0.281,0.188 10 false K7 2.49,1.26 2.906,1.458 0.417,0.198 10 false GND 0.781,1.25 0.99,1.458 0.208,0.208 10 false B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K7-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Component with harness connected
(Front Power Window Regulator Motor Assembly LH)


OK

4.PERFORM ACTIVE TEST USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.


HINT:

Up and down movement does not occur if the arrow is not pressed and held.


D-Door Motor (for LHD)
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

P-Door Motor (for RHD)
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

OK:

Power window regulator motor operates.




OK

5.PERFORM INITIALIZATION

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

5.PERFORM INITIALIZATION
a.

Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.




NEXT

6.CHECK POWER WINDOW CONTROL SYSTEM
6.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

HINT:

Check the power window operation of the window for which DTC B2311 has been stored.


OK:

Power window operates normally.




OK

7.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

7.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.




OK

END (OVERHEATED FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)
a.
U169637E02
1.854,1.125 2.438,1.323 false 1.563,1.115 0.958,1.313 false 1.625,0.385 1.896,0.563 0.271,0.177 10 false J7 2.49,1.271 2.906,1.469 0.417,0.198 10 false GND 0.781,1.25 0.927,1.448 0.146,0.198 10 false B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J7-1 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J7-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Component with harness connected
(Front Power Window Regulator Motor Assembly RH)


OK

9.PERFORM ACTIVE TEST USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.


HINT:

Up and down movement does not occur if the arrow is not pressed and held.


D-Door Motor (for RHD)
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

P-Door Motor (for LHD)
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

OK:

Power window regulator motor operates.




OK

10.PERFORM INITIALIZATION

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

10.PERFORM INITIALIZATION
a.

Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.




NEXT

11.CHECK POWER WINDOW CONTROL SYSTEM
11.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

HINT:

Check the power window operation of the window for which DTC B2311 has been stored.


OK:

Power window operates normally.




OK

12.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.




OK

END (OVERHEATED FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
U169638E02
1.854,1.125 2.438,1.323 false 1.563,1.125 0.958,1.323 false 1.594,0.385 1.854,0.563 0.26,0.177 10 false M4 2.479,1.271 2.917,1.469 0.438,0.198 10 false GND 0.781,1.271 0.969,1.479 0.188,0.208 10 false B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-1 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M4-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Component with harness connected
(Rear Power Window Regulator Motor Assembly LH)


OK

14.PERFORM ACTIVE TEST USING GTS (RL-DOOR MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.PERFORM ACTIVE TEST USING GTS (RL-DOOR MOTOR)
a.

Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.


HINT:

Up and down movement does not occur if the arrow is not pressed and held.


RL-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

OK:

Power window regulator motor operates.




OK

15.PERFORM INITIALIZATION

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

15.PERFORM INITIALIZATION
a.

Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.




NEXT

16.CHECK POWER WINDOW CONTROL SYSTEM
16.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

HINT:

Check the power window operation of the window for which DTC B2311 has been stored.


OK:

Power window operates normally.




OK

17.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

17.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.




OK

END (OVERHEATED REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

18.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
U169639E02
1.854,1.125 2.438,1.323 false 1.563,1.125 0.958,1.323 false 1.615,0.385 1.865,0.573 0.25,0.188 10 false L4 2.49,1.26 2.917,1.458 0.427,0.198 10 false GND 0.781,1.25 0.969,1.458 0.188,0.208 10 false B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-1 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L4-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Component with harness connected
(Rear Power Window Regulator Motor Assembly RH)


OK

19.PERFORM ACTIVE TEST USING GTS (RR-DOOR MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.PERFORM ACTIVE TEST USING GTS (RR-DOOR MOTOR)
a.

Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.


HINT:

Up and down movement does not occur if the arrow is not pressed and held.


RR-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF/UP/DOWN -

OK:

Power window regulator motor operates.




OK

20.PERFORM INITIALIZATION

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

20.PERFORM INITIALIZATION
a.

Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.




NEXT

21.CHECK POWER WINDOW CONTROL SYSTEM
21.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

HINT:

Check the power window operation of the window for which DTC B2311 has been stored.


OK:

Power window operates normally.




OK

22.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

22.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.




OK

END (OVERHEATED REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY