Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2020.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B1247 Tire Pressure Monitor Receiver Communication Stop In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


This DTC is for main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C408641E08
4.083,1.958 7.052,2.188 2.969,0.229 10 false Main Body ECU (Multiplex Network Body ECU) 4.073,1.771 4.531,1.969 0.458,0.198 10 false G218 0.385,1.771 0.844,1.969 0.458,0.198 10 false R41 0.385,1.969 3.354,2.198 2.969,0.229 10 false Tire Pressure Warning ECU and Receiver 4.656,1.031 5.115,1.229 0.458,0.198 10 false RDA 4.385,0.917 4.635,1.115 0.25,0.198 10 false 4 2.573,0.917 2.823,1.115 0.25,0.198 10 false 4 2.156,0.917 2.615,1.115 0.458,0.198 10 false RDA 1.26,1.115 1.719,1.313 0.458,0.198 10 false CPU

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

Click here

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (OUTPUT WAVEFORM)
a.
C385229C57
1.229,0.219 1.667,0.479 0.438,0.26 1.042,1.792 1.365,1.146 true 0.292,0.271 0.604,0.469 0.313,0.198 10 false *a 2.875,3.396 3.188,3.594 0.313,0.198 10 false *b 0.927,1.823 1.406,2.063 0.479,0.24 10 false RDA 1.354,0.271 1.667,0.469 0.313,0.198 10 false R41
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition
R41-4 (RDA) - Body ground 5 V/DIV.5 ms./DIV. Ignition switch ON Waveform generation



Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 10.5 V or higher and 0.5 V or less) A
Waveform does not change from 10.5 V or higher B
Waveform does not change from 0.5 V or less C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

C

2.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
2.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
a.
C375025C59
0.281,0.917 0.677,1.177 0.396,0.26 1.854,1.167 2.646,0.448 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 2.719,0.385 3.177,0.583 0.458,0.198 10 false RDA 0.344,0.969 0.802,1.167 0.458,0.198 10 false R41
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the tire pressure warning ECU and receiver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R41-4 (RDA) - Body ground Ignition switch ON 10.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Turn the ignition switch off.


b.

Disconnect the G218 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G218-4 (RDA) - R41-4 (RDA) Always Below 1 Ω
G218-4 (RDA) or R41-4 (RDA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR