Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit  


DESCRIPTION

When the brakes are applied by the dynamic radar cruise control system, the skid control ECU (master cylinder solenoid) operates the stop light switch assembly to illuminate the stop lights.

Condition 1:
·

If the ECM receives a signal from the skid control ECU (master cylinder solenoid) indicating a malfunction of the stop light control relay, DTC P0571 is stored.


When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM.

The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control.

Condition 2:
·

When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P0571 is stored.


DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Stop Light Switch Circuit
Condition 1:
·

When the dynamic radar cruise control system is operating, the ECM detects a signal indicating a stop light control relay malfunction from the skid control ECU (master cylinder solenoid) for approximately 1 second or more.


Condition 2:
·

When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.


Condition 1:
·

Harness or connector

·

Stop light switch assembly

·

Skid control ECU (master cylinder solenoid)


Condition 2:
·

Harness or connector

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

for 1GR-FE:
C448905E07
2.438,2.219 4.354,2.469 1.917,0.25 10 false Stop Light Switch Assembly 2.583,3.49 4.188,3.979 1.604,0.49 10 false Skid Control ECU (Master Cylinder Solenoid) 4.771,4.823 7.094,5.417 2.323,0.594 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly) 5.427,3.604 6.958,3.969 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 4.042,2.969 4.583,3.208 0.542,0.24 10 false 45 2.594,3.302 3.135,3.542 0.542,0.24 10 false A7 0.438,0.594 1.448,0.792 1.01,0.198 10 false from Battery 0.281,1.396 1.771,1.74 1.49,0.344 10 false from IG2 Relay 6.094,2.292 6.635,2.531 0.542,0.24 10 false ECM 3.979,0.479 4.229,0.719 0.25,0.24 10 false 3 5.75,0.74 6.292,0.979 0.542,0.24 10 false STP 5.75,1.531 6.292,1.771 0.542,0.24 10 false ST1- 3.979,1.25 4.229,1.49 0.25,0.24 10 false 5 5.396,1.281 5.865,1.469 0.469,0.188 10 false 34 1.917,0.781 2.927,0.979 1.01,0.198 10 false STOP 1.969,1.563 2.323,1.771 0.354,0.208 10 false IGN 2.427,2.042 2.813,2.271 0.385,0.229 10 false A99 2.604,1.281 2.854,1.521 0.25,0.24 10 false 6 3.979,1.573 4.229,1.813 0.25,0.24 10 false 2 4.781,4.646 5.833,4.844 1.052,0.198 10 false G45 5.76,3.063 6.302,3.302 0.542,0.24 10 false STP1 5.75,4.406 6.292,4.646 0.542,0.24 10 false STP 5.563,4.302 6.104,4.542 0.542,0.24 10 false 6 5.427,3.427 5.969,3.667 0.542,0.24 10 false G213 5.563,2.948 6.104,3.188 0.542,0.24 10 false 2 3.573,3.073 4.115,3.354 0.542,0.281 10 false STP2 3.583,1.573 4.042,1.771 0.458,0.198 10 false GND 2.573,0.5 2.823,0.74 0.25,0.24 10 false 7 2.792,0.49 3.042,0.729 0.25,0.24 10 false B 3.781,1.26 4.031,1.5 0.25,0.24 10 false L 2.792,1.271 3.042,1.51 0.25,0.24 10 false B 3.792,0.49 4.042,0.729 0.25,0.24 10 false L 3.281,1.104 3.594,1.302 0.313,0.198 10 false IC 5.396,0.49 5.896,0.698 0.5,0.208 10 false 35 6.083,2.135 6.542,2.333 0.458,0.198 10 false G56

for 2TR-FE:
C448905E08
2.438,2.219 4.354,2.469 1.917,0.25 10 false Stop Light Switch Assembly 1.771,3.458 4.76,3.781 2.99,0.323 10 false Skid Control ECU (Master Cylinder Solenoid) 4.74,4.823 7.063,5.417 2.323,0.594 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly) 5.427,3.604 6.958,3.969 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly)*2 4.021,2.958 4.896,3.177 0.875,0.219 10 false 45 1.792,3.24 2.563,3.458 0.771,0.219 10 false A7 0.5,0.594 1.51,0.792 1.01,0.198 10 false from Battery 0.344,1.396 1.833,1.74 1.49,0.344 10 false from IG2 Relay 6.073,2.271 6.615,2.51 0.542,0.24 10 false ECM 3.979,0.479 4.229,0.719 0.25,0.24 10 false 3 5.688,0.75 6.229,0.99 0.542,0.24 10 false STP 5.708,1.531 6.25,1.771 0.542,0.24 10 false ST1- 6.042,2.104 6.542,2.344 0.5,0.24 10 false G180 3.979,1.25 4.229,1.49 0.25,0.24 10 false 5 5.406,0.49 6.25,0.698 0.844,0.208 10 false 10 5.406,1.292 6.198,1.479 0.792,0.188 10 false 11 1.938,0.781 2.948,0.979 1.01,0.198 10 false STOP 1.99,1.563 2.344,1.771 0.354,0.208 10 false IGN 2.427,2.042 2.813,2.271 0.385,0.229 10 false A99 2.604,1.281 2.854,1.521 0.25,0.24 10 false 6 3.979,1.573 4.229,1.813 0.25,0.24 10 false 2 4.729,4.646 5.781,4.844 1.052,0.198 10 false G150*1, G45*2 5.76,3.063 6.302,3.302 0.542,0.24 10 false STP1 5.75,4.406 6.292,4.646 0.542,0.24 10 false STP 5.146,4.281 5.844,4.51 0.698,0.229 10 false 4*1, 6*2 5.427,3.427 5.969,3.667 0.542,0.24 10 false G213 5.552,2.948 6.01,3.198 0.458,0.25 10 false 2 3.531,3.073 4.073,3.354 0.542,0.281 10 false STP2 3.583,1.573 4.042,1.771 0.458,0.198 10 false GND 2.573,0.5 2.823,0.74 0.25,0.24 10 false 7 2.792,0.49 3.042,0.729 0.25,0.24 10 false B 3.781,1.26 4.031,1.5 0.25,0.24 10 false L 2.792,1.271 3.042,1.51 0.25,0.24 10 false B 3.792,0.49 4.042,0.729 0.25,0.24 10 false L 3.281,1.104 3.594,1.302 0.313,0.198 10 false IC 0.167,4.74 3.052,5.125 2.885,0.385 10 false *1: w/o Entry and Start System 0.146,5.271 3.031,5.656 2.885,0.385 10 false *2: w/ Entry and Start System 5.031,2.948 5.344,3.146 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTCs
a.

Check if vehicle stability control system (for hydraulic brake booster) DTCs are output.


Result:
Result Proceed to
Vehicle stability control system (for hydraulic brake booster) DTCs are not output A
Vehicle stability control system (for hydraulic brake booster) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.
C367136C05
1.469,0.135 1.969,0.385 0.5,0.25 0.719,1.792 1.292,1.083 true 1.958,1.813 2.083,1.104 true 2.615,1.823 2.344,1.083 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.563,1.813 0.906,1.99 0.344,0.177 10 false GND 1.906,1.823 2.146,2 0.24,0.177 10 false B 2.583,1.823 2.823,2 0.24,0.177 10 false B 1.594,0.177 1.938,0.354 0.344,0.177 10 false A99
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-6 (B) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A99-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

for 1GR-FE:

i.

Disconnect the G56 ECM connector.


ii.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


iii.

Disconnect the A99 stop light switch assembly connector.


iv.

Disconnect the G45 shift lock control ECU (transmission floor shift assembly) connector.


v.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G56-34 (ST1-) - A99-5 (L) Always Below 1 Ω
G56-35 (STP) - A99-3 (L) Always Below 1 Ω
G56-34 (ST1-) or A99-5 (L) - Body ground Always 10 kΩ or higher
G56-35 (STP) or A99-3 (L) - Body ground Always 10 kΩ or higher




b.

for 2TR-FE:

i.

Disconnect the G180 ECM connector.


ii.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


iii.

Disconnect the A99 stop light switch assembly connector.


iv.

Disconnect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


v.

w/ Entry and Start System:

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G180-11 (ST1-) - A99-5 (L) Always Below 1 Ω
G180-10 (STP) - A99-3 (L) Always Below 1 Ω
G180-11 (ST1-) or A99-5 (L) - Body ground Always 10 kΩ or higher
G180-10 (STP) or A99-3 (L) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR