Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM C

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17AC  Transfer Shift Motor Limit Switch Circuit  


DESCRIPTION

When the transfer shift actuator assembly is switching between high (H4*1, H4F or H4L*2) and low (L4*, L4L*2), the HL1 and HL2 terminals are in one of the ON/OFF combinations listed in the table below.

*1: for 1GR-FE or 1GD-FTV

*2: for 2TR-FE or 5L-E


Terminal Mode
HIGH (H4*1, H4F or H4L*2) Switching LOW (L4*1, L4L*2)
HL1 OFF ON ON
HL2 ON ON OFF

*1: for 1GR-FE or 1GD-FTV

*2: for 2TR-FE or 5L-E


A malfunction is detected depending on the combination of the 2 circuits that make up the high-low transfer limit switch.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17AC
1.

When switching between high and low (high-low transfer shift motor operating) while the ignition switch is turned to ON or directly after the ignition switch is turned to ON

2.

The combination of HL1 and HL2 does not match

3.

0.05 seconds or more (if directly after ignition switch is turned to ON, 1 second or more)

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C384949E01
1.094,3.115 1.406,3.302 0.313,0.188 10 false C43 1.094,3.271 3.188,3.448 2.094,0.177 10 false Transfer Shift Actuator Assembly 4.938,3.125 5.25,3.313 0.313,0.188 10 false G53 4.948,3.281 6.719,3.458 1.771,0.177 10 false 4 Wheel Drive Control ECU 1.729,2.698 2.604,2.875 0.875,0.177 10 false Limit Switch 1.125,2.167 1.583,2.344 0.458,0.177 10 false GND1 2.99,2.177 3.302,2.354 0.313,0.177 10 false HL2 2.99,1.5 3.302,1.677 0.313,0.177 10 false HL1 3.375,1.5 3.604,1.677 0.229,0.177 10 false 12 3.375,2.177 3.604,2.354 0.229,0.177 10 false 11 0.917,2.177 1.083,2.354 0.167,0.177 10 false 6 4.708,2.177 4.875,2.354 0.167,0.177 10 false 7 4.708,1.49 4.875,1.667 0.167,0.177 10 false 8 4.927,1.5 5.24,1.677 0.313,0.177 10 false HL1 4.927,2.177 5.24,2.354 0.313,0.177 10 false HL2 5.604,0.365 5.823,0.542 0.219,0.177 10 false IG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

Disconnect the C43 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-8 (HL1) - C43-12 (HL1) Always Below 1 Ω
G53-7 (HL2) - C43-11 (HL2) Always Below 1 Ω
C43-6 (GND1) - Body ground Always Below 1 Ω
G53-8 (HL1) or C43-12 (HL1) - Body ground Always 10 kΩ or higher
G53-7 (HL2) or C43-11 (HL2) - Body ground Always 10 kΩ or higher




OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
C325622E06
1.479,0.583 1.917,0.833 0.438,0.25 1.792,2.448 2.115,1.99 true 2.719,2.448 2.406,2.01 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.552,0.635 1.865,0.833 0.313,0.198 10 false C43 1.656,2.5 1.969,2.698 0.313,0.198 10 false HL2 2.615,2.5 2.927,2.698 0.313,0.198 10 false HL1

a.

Disconnect the C43 transfer shift actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C43-12 (HL1) - Body ground Ignition switch ON 10.5 to 14 V
C43-11 (HL2) - Body ground Ignition switch ON 10.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU