Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM J

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  Clutch Switch Circuit  


DESCRIPTION

for 1GR-FE, 1GD-FTV:

While depressing the clutch pedal, the clutch start switch assembly sends a signal to terminal MTN of the 4 wheel drive control ECU. While the signal is input, switching between H4 and L4 is possible.

for 2TR-FE, 5L-E:

While depressing the clutch pedal, the clutch start switch assembly sends a signal to terminal MTN of the 4 wheel drive control ECU. While the signal is input, switching between H4L and L4L is possible.

WIRING DIAGRAM

C385082E03
0.729,0.188 1.458,0.365 0.729,0.177 10 false from ECM 0.719,0.531 2.583,0.875 1.865,0.344 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.698,1.167 2.146,1.354 1.448,0.188 10 false from Ignition Switch*2 0.313,2.073 1.115,2.271 0.802,0.198 10 false to ST Relay 0.146,3.229 2.51,3.417 2.365,0.188 10 false *1: w/ Smart Entry and Start System 1.469,2.552 2.479,2.75 1.01,0.198 10 false A40*1*3 2.594,2.719 4.51,2.917 1.917,0.198 10 false Clutch Start Switch Assembly 0.167,3.49 2.531,3.677 2.365,0.188 10 false *2: w/o Smart Entry and Start System 3.521,1.948 3.677,2.125 0.156,0.177 10 false 2 1.688,1.958 1.844,2.135 0.156,0.177 10 false 1 4.802,1.958 5,2.146 0.198,0.188 10 false 18 4.927,3 5.344,3.177 0.417,0.177 10 false G53 4.938,3.156 6.656,3.333 1.719,0.177 10 false 4 Wheel Drive Control ECU 5.094,1.938 5.458,2.115 0.365,0.177 10 false MTN 6.052,1.313 6.26,1.49 0.208,0.177 10 false IG 2.604,3.25 3.385,3.427 0.781,0.177 10 false *3: for LHD 2.615,3.5 3.396,3.677 0.781,0.177 10 false *4: for RHD 1.469,2.719 2.354,2.896 0.885,0.177 10 false r1*1*4 1.469,3.042 2.385,3.24 0.917,0.198 10 false r2*2*4 1.469,2.885 2.719,3.094 1.25,0.208 10 false A41*2*3

PROCEDURE

1.READ VALUE USING GTS (CLUTCH START SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Clutch SW Clutch start switch status
ON or OFF
ON: Clutch pedal depressed
OFF: Clutch pedal released
Used only for vehicles with a manual transmission.
Displays OFF for vehicles with an automatic transmission.

OK:

The display changes according to the clutch pedal operation.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK ENGINE CONTROL SYSTEM
3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

for LHD:

w/ Smart Entry and Start System:

Disconnect the A40 clutch start switch assembly connector.

w/o Smart Entry and Start System:

Disconnect the A41 clutch start switch assembly connector.


c.

for RHD:

w/ Smart Entry and Start System:

Disconnect the r1 clutch start switch assembly connector.

w/o Smart Entry and Start System:

Disconnect the r2 clutch start switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
w/ Smart Entry and Start System
Tester Connection Condition Specified Condition
G53-18 (MTN) - A40-1 Always Below 1 Ω
G53-18 (MTN) or A40-1 - Body ground Always 10 kΩ or higher

w/o Smart Entry and Start System
Tester Connection Condition Specified Condition
G53-18 (MTN) - A41-1 Always Below 1 Ω
G53-18 (MTN) or A41-1 - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
w/ Smart Entry and Start System
Tester Connection Condition Specified Condition
G53-18 (MTN) - r1-1 Always Below 1 Ω
G53-18 (MTN) or r1-1 - Body ground Always 10 kΩ or higher

w/o Smart Entry and Start System
Tester Connection Condition Specified Condition
G53-18 (MTN) - r2-1 Always Below 1 Ω
G53-18 (MTN) or r2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR