Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM T

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



3 Drive Mode (H4F, H4L, or L4L) (for 2TR-FE or 5L-E)
Symptom Suspected Area See page
Noise Oil (Level low) (Click here)
Oil (Wrong) (Click here)
Transfer faulty (Click here)
Oil leakage Oil (Level too high) (Click here)
Gasket (Damaged) (Click here)
Oil seal (Worn or damaged) (Click here)
O-ring (Worn or damaged) (Click here)
While in H4F, even when the transfer position switch is turned to a position other than H4F, the center differential lock indicator light and 4LO indicator light do not illuminate ECU power source circuit (Click here)
CAN communication system (Click here)
Combination meter assembly
Transfer position switch
4 wheel drive control ECU
While in H4L, even when the transfer position switch is turned to a position other than H4L, the center differential lock indicator light remains on and the 4LO indicator light does not illuminate ECU power source circuit (Click here)
Clutch start switch circuit (for Manual Transmission) (Click here)
Transfer position switch (Click here)
4 wheel drive control ECU
While in L4L, even when the transfer position switch is turned to a position other than L4L, the center differential lock indicator light and 4LO indicator light remain illuminated ECU power source circuit (Click here)
Transfer position switch (Click here)
4 wheel drive control ECU
CAN communication system
The 4LO indicator light continues blinking after the transfer position switch is operated ECU power source circuit (Click here)
High-low transfer shift motor (Click here)
High-low transfer limit switch
4 wheel drive control ECU
The center differential lock indicator light continues blinking after the transfer position switch is operated ECU power source circuit (Click here)
Center differential lock shift motor (Click here)
Center differential lock limit switch or center differential lock detection switch
4 wheel drive control ECU

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)


4 Drive Mode (H4F, H4L, L4F or L4L) (for 1GR-FE or 1GD-FTV)
Symptom Suspected Area See page
Noise Oil (Level low) (Click here)
Oil (Wrong) (Click here)
Transfer faulty (Click here)
Oil leakage Oil (Level too high) (Click here)
Gasket (Damaged) (Click here)
Oil seal (Worn or damaged) (Click here)
O-ring (Worn or damaged) (Click here)
The 4LO indicator light remains off after operating the transfer position switch (combination switch assembly) to L4*1
The 4LO indicator light remains off after operating the transfer position switch to L4*2
ECU power source circuit (Click here)
Clutch switch circuit*4 (Click here)
CAN communication system (Click here)
Combination meter assembly
Transfer position switch (combination switch assembly) *1
Transfer position switch*2
4 wheel drive control ECU
The 4LO indicator light remains on after operating the transfer position switch (combination switch assembly) to H4*1
The 4LO indicator light remains on after operating the transfer position switch to H4*2
ECU power source circuit (Click here)
Clutch switch circuit*4 (Click here)
CAN communication system (Click here)
Combination meter assembly
Transfer position switch (combination switch assembly) *1
Transfer position switch*2
4 wheel drive control ECU
The 4LO indicator light continues blinking after the transfer position switch (combination switch assembly) is operated*1
The 4LO indicator light continues blinking after the transfer position switch is operated*2
ECU power source circuit (Click here)
High-low transfer shift motor (Click here)
High-low transfer limit switch
4 wheel drive control ECU
After the center differential lock switch (combination switch assembly) is operated, the center differential lock indicator light remains off or illuminated*1
After the center differential lock switch (No. 2 combination switch assembly) is operated, the center differential lock indicator light remains off or illuminated*2*3
After the center differential lock switch is operated, the center differential lock indicator light remains off or illuminated*2*4
ECU power source circuit (Click here)
CAN communication system (Click here)
Combination meter assembly
Center differential lock switch (combination switch assembly)*1
Center differential lock switch (No. 2 combination switch assembly)*2*3
Center differential lock switch*2*4
4 wheel drive control ECU
After the center differential lock switch (combination switch assembly) is operated, the center differential lock indicator light remains blinking*1
After the center differential lock switch (No. 2 combination switch assembly) is operated, the center differential lock indicator light remains blinking*2*3
After the center differential lock switch is operated, the center differential lock indicator light remains blinking*2 *4
ECU power source circuit (Click here)
Center differential lock shift motor (Click here)
Center differential lock limit switch or center differential lock detection switch
4 wheel drive control ECU

*1: for 1GR-FE, 1GD-FTV w/ Combination Switch

*2: for 1GR-FE, 1GD-FTV w/o Combination Switch

*3: for Automatic Transmission

*4: for Manual Transmission


Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)