Turn the ignition switch to ON.
Check the center differential lock indicator light.
for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission):
Press the center differential lock switch (combination switch assembly).
for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission):
Press the center differential lock switch (No. 2 combination switch assembly).
for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission):
Press the center differential lock switch.
After 60 seconds, check the center differential lock indicator light.
| Result | Proceed to |
|---|---|
| The center differential lock indicator light blinks, turns off or illuminates | A |
| Center differential lock indicator light remains off regardless of switch operation | B |
| Center differential lock indicator remains illuminated regardless of switch operation | C |
| Center differential lock indicator light rapidly blinks | D |
Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A
B
C
D
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus (w/ Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM, w/o Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to | |
|---|---|---|
| DTC is not output | A | |
| DTC is output | w/ Central Gateway ECU | B |
| w/o Central Gateway ECU | C | |
A
B
C
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Center Differential Lock Control SW | Center differential lock switch status/
ON or OFF |
ON: Switch pressed and held
OFF: Switch not pressed |
- |
for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission):
Display changes according to center differential lock switch (combination switch assembly) operation.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission):
Display changes according to center differential lock switch (No. 2 combination switch assembly) operation.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission):
Display changes according to center differential lock switch operation.
OK
NG
Turn the ignition switch off.
Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
Check the combination meter assembly.
The center differential lock indicator light turns on or off in accordance with the GTS.
OK
NG
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission):
Remove the center differential lock switch (combination switch assembly) (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/ Combination Switch)>REMOVAL).
Inspect the center differential lock switch (combination switch assembly) (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/ Combination Switch)>INSPECTION).
The center differential lock switch (combination switch assembly) operates normally.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission):
Remove the center differential lock switch (No. 2 combination switch assembly) (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)>REMOVAL).
Inspect the center differential lock switch (No. 2 combination switch assembly) (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)>INSPECTION).
The center differential lock switch (No. 2 combination switch assembly) operates normally.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission):
Remove the center differential lock switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)>REMOVAL).
Inspect the center differential lock switch (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)>INSPECTION).
The center differential lock switch operates normally.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission) or | B |
| for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission) | C | |
| for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission) | D | |
A
B
C
(Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)>REMOVAL)
D
Disconnect the G53 4 wheel drive control ECU connector.
for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission):
Disconnect the G156 center differential lock switch (combination switch assembly) connector.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission):
Disconnect the G156 center differential lock switch (No. 2 combination switch assembly) connector.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission):
Disconnect the G230 center differential lock switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-6 (DL) - G156-3 (CPU) | Always | Below 1 Ω |
| G156-24 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-6 (DL) - G230-5 (CPU) | Always | Below 1 Ω |
| G230-2 (L) - Body ground | Always | Below 1 Ω |
OK
NG
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus (w/ Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM, w/o Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
"Bus Check" indicates no malfunctions in CAN communication.
| Result | Proceed to | |
|---|---|---|
| DTC is not output | A | |
| DTC is output | w/ Central Gateway ECU | B |
| w/o Central Gateway ECU | C | |
A
B
C
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Center Differential Lock Indicator Request | Center differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF |
·
Blink3: Indicator light rapidly blinks ·
Blink2: Indicator light blinks 3 times ·
Blink1: Indicator light blinks ·
ON: Indicator light illuminates ·
OFF: Indicator light turns off |
·
Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off) ·
Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off) |
for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission):
Turn the differential lock switch (combination switch assembly) on and off several times and check the GTS display condition of the center differential lock indicator light.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission):
Turn the differential lock switch (No. 2 combination switch assembly) on and off several times and check the GTS display condition of the center differential lock indicator light.
for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission):
Turn the differential lock switch on and off several times and check the GTS display condition of the center differential lock indicator light.
| Result | Proceed to |
|---|---|
| Data List continues to display ON even when center differential lock switch (combination switch assembly) is operated*1
Data List continues to display ON even when center differential lock switch (No. 2 combination switch assembly) is operated*2 Data List continues to display ON even when center differential lock switch is operated*3 |
A |
| Data List display changes according to center differential lock switch (combination switch assembly) operation*1
Data List display changes according to center differential lock switch (No. 2 combination switch assembly) operation*2 Data List display changes according to center differential lock switch operation*3 |
B |
*1: for 1GR-FE, 1GD-FTV w/ Combination Switch (Automatic Transmission)
*2: for 1GR-FE, 1GD-FTV w/o Combination Switch (Automatic Transmission)
*3: for 1GR-FE, 1GD-FTV w/o Combination Switch (Manual Transmission)
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)