Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617  Front Airbag Sensor Lost Communication (LH)  B1618  Front Airbag Sensor Initialization Error (LH)  


DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1617 or B1618 is stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1617 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Center airbag sensor


B1618 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Center airbag sensor



WIRING DIAGRAM

C213916E04
5.584,3.826 5.803,3.997 0.218,0.171 10 G1 0.438,3.858 0.740,4.029 0.302,0.171 10 A21 1.717,0.889 2.018,1.060 0.302,0.171 10 2 1.717,2.073 2.018,2.244 0.302,0.171 10 1 5.31,0.889 5.612,1.060 0.302,0.171 10 30 5.31,2.073 5.612,2.244 0.302,0.171 10 28 3.692,0.798 3.813,0.969 0.121,0.171 10 3 3.692,1.982 3.813,2.153 0.121,0.171 10 4 3.588,0.992 3.898,1.163 0.309,0.171 10 GA5 3.588,2.169 3.898,2.340 0.309,0.171 10 GA5 5.622,0.994 5.923,1.165 0.302,0.171 10 +SL 5.622,2.161 5.923,2.332 0.302,0.171 10 -SL 1.292,0.994 1.594,1.165 0.302,0.171 10 +SL 1.292,2.161 1.594,2.332 0.302,0.171 10 -SL 0.438,4.012 2.003,4.185 1.566,0.173 10 Front Airbag Sensor LH 5.584,3.998 6.974,4.196 1.390,0.198 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front airbag sensor LH.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front airbag sensor LH.


b.
C384699C01
0.094,2.573 0.406,2.771 0.313,0.198 10 false *B 0.094,0.448 0.406,0.646 0.313,0.198 10 false *A 2.552,1.844 2.865,2.042 0.313,0.198 10 false *2 0.531,1.49 0.844,1.688 0.313,0.198 10 false *1 0.542,3.698 0.854,3.896 0.313,0.198 10 false *1 2.531,3.792 2.844,3.99 0.313,0.198 10 false *2
*A w/o Side Airbag
*B w/ Side Airbag
*1 Front Airbag Sensor RH
*2 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side and front airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

NG

REPLACE ENGINE ROOM MAIN WIRE OR INSTRUMENT PANEL WIRE

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
a.

w/o Side Airbag

i.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U148513E01
0.438,0.561 0.555,0.727 0.118,0.166 10 F 0.704,0.729 0.822,0.895 0.118,0.166 10 E 0.96,0.729 1.077,0.895 0.118,0.166 10 D 1.058,0.729 1.175,0.895 0.118,0.166 10 C 1.31,0.729 1.427,0.895 0.118,0.166 10 B 1.55,0.564 1.667,0.730 0.118,0.166 10 A 0.143,0.907 0.306,1.046 0.163,0.139 10 *1 1.446,1.181 1.609,1.319 0.163,0.139 10 *2 2.64,0.46 2.938,0.609 0.298,0.149 10 A21 4.984,0.464 5.230,0.613 0.246,0.149 10 G1 3.501,0.154 3.685,0.319 0.184,0.165 10 *a 4.118,0.499 4.301,0.655 0.184,0.156 10 *3 5.976,0.116 6.160,0.282 0.184,0.165 10 *b 6.677,0.499 6.861,0.655 0.184,0.156 10 *4 5.547,1.424 5.730,1.580 0.184,0.156 10 *5 6.322,1.247 6.608,1.430 0.286,0.184 10 -SL 2.946,1.233 3.231,1.416 0.286,0.184 10 -SL 5.164,1.247 5.449,1.430 0.286,0.184 10 +SL 4.043,1.19 4.329,1.374 0.286,0.184 10 +SL 3.702,0.824 4.043,1.212 false 3.529,0.829 3.184,1.268 false 5.839,0.911 6.329,1.261 false 5.66,0.918 5.422,1.254 false 5.701,1.312 5.654,1.405 false

Text in Illustration
*1 Front Airbag Sensor LH *2 Center Airbag Sensor
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A21-2 (+SL) - Body ground Ignition switch ON Below 1 V
A21-1 (-SL) - Body ground Ignition switch ON Below 1 V



iii.

Turn the ignition switch off.


iv.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


v.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-2 (+SL) - A21-1 (-SL) Always Below 1 Ω



vii.

Disconnect the service wire from connector B.


viii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-2 (+SL) - A21-1 (-SL) Always 1 MΩ or higher
A21-2 (+SL) - Body ground Always 1 MΩ or higher
A21-1 (-SL) - Body ground Always 1 MΩ or higher




b.

w/ Side Airbag

i.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256539C10
2.521,0.667 2.885,0.896 0.365,0.229 4.823,0.635 5.188,0.865 0.365,0.229 5.729,1.469 5.729,1.333 false 3.135,1.208 3.521,0.823 false 4.083,1.208 3.667,0.833 false 6.26,1.323 5.844,0.948 false 5.25,1.292 5.635,0.927 false 0.333,1.156 0.646,1.313 0.313,0.156 10 false *1 1.708,1.24 2.021,1.396 0.313,0.156 10 false *2 4.104,0.604 4.417,0.76 0.313,0.156 10 false *3 6.677,0.563 6.99,0.719 0.313,0.156 10 false *4 5.667,1.5 5.979,1.656 0.313,0.156 10 false *5 1.594,0.771 1.75,0.927 0.156,0.156 10 false A 3.51,0.156 3.823,0.313 0.313,0.156 10 false *a 5.99,0.104 6.302,0.26 0.313,0.156 10 false *b 1.302,0.99 1.458,1.146 0.156,0.156 10 false B 1.042,0.99 1.198,1.146 0.156,0.156 10 false C 0.938,0.99 1.094,1.146 0.156,0.156 10 false D 0.688,0.969 0.844,1.125 0.156,0.156 10 false E 0.406,0.75 0.563,0.906 0.156,0.156 10 false F 2.979,1.25 3.292,1.406 0.313,0.156 10 false -SL 3.948,1.25 4.26,1.406 0.313,0.156 10 false +SL 6.229,1.385 6.542,1.542 0.313,0.156 10 false -SL 5.083,1.323 5.396,1.479 0.313,0.156 10 false +SL 2.604,0.698 2.917,0.854 0.313,0.156 10 false A21 4.948,0.677 5.26,0.833 0.313,0.156 10 false G1
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A21-2 (+SL) - Body ground Ignition switch ON Below 1 V
A21-1 (-SL) - Body ground Ignition switch ON Below 1 V



iii.

Turn the ignition switch off.


iv.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


v.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-2 (+SL) - A21-1 (-SL) Always Below 1 Ω



vii.

Disconnect the service wire from connector B.


viii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-2 (+SL) - A21-1 (-SL) Always 1 MΩ or higher
A21-2 (+SL) - Body ground Always 1 MΩ or higher
A21-1 (-SL) - Body ground Always 1 MΩ or higher





OK

4.CHECK FRONT AIRBAG SENSOR LH

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)
4.CHECK FRONT AIRBAG SENSOR LH
a.
C384698C01
0.115,0.125 0.427,0.323 0.313,0.198 10 false *A 0.063,2.667 0.375,2.865 0.313,0.198 10 false *B 0.75,1.552 1.063,1.75 0.313,0.198 10 false *1 2.344,1.917 2.656,2.115 0.313,0.198 10 false *2 0.74,3.792 1.052,3.99 0.313,0.198 10 false *1 2.333,3.917 2.646,4.115 0.313,0.198 10 false *2
*A w/o Side Airbag
*B w/ Side Airbag
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor


Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1617 or B1618 is output A
DTC B1612 or B1613 is output B
DTC B1612, B1613, B1617 and B1618 are not output C

HINT:

Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.




C

A

B

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)
a.

w/o Side Airbag

i.

Disconnect the instrument panel wire connector from the engine room main wire.

U148514E01
0.452,0.509 0.569,0.676 0.118,0.166 10 F 0.718,0.677 0.836,0.844 0.118,0.166 10 E 0.974,0.677 1.091,0.844 0.118,0.166 10 D 1.128,0.677 1.245,0.844 0.118,0.166 10 C 1.38,0.677 1.498,0.844 0.118,0.166 10 B 1.662,0.513 1.779,0.679 0.118,0.166 10 A 0.129,0.856 0.292,0.995 0.163,0.139 10 *1 1.544,1.129 1.707,1.268 0.163,0.139 10 *2 0.809,0.394 0.972,0.532 0.163,0.139 10 *3 1.229,0.394 1.392,0.532 0.163,0.139 10 *4 2.574,0.506 2.900,0.655 0.325,0.149 10 GA5 4.939,0.51 5.176,0.659 0.237,0.149 10 G1 3.459,0.196 3.643,0.361 0.184,0.165 10 *a 4.076,0.541 4.259,0.697 0.184,0.156 10 *5 5.934,0.158 6.118,0.324 0.184,0.165 10 *b 6.635,0.541 6.819,0.697 0.184,0.156 10 *6 5.505,1.466 5.688,1.622 0.184,0.156 10 *7 6.28,1.289 6.566,1.472 0.286,0.184 10 -SL 2.868,1.345 3.154,1.528 0.286,0.184 10 +SL 5.122,1.289 5.407,1.472 0.286,0.184 10 +SL 4.059,1.345 4.345,1.528 0.286,0.184 10 -SL 3.688,1.249 4.015,1.422 false 3.499,1.27 3.156,1.422 false 5.797,0.953 6.287,1.303 false 5.618,0.96 5.38,1.296 false 5.671,1.319 5.629,1.459 false

Text in Illustration
*1 Front Airbag Sensor LH *2 Center Airbag Sensor
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


ii.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GA5-3 (+SL) - Body ground Ignition switch ON Below 1 V
GA5-4 (-SL) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


vi.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



vii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GA5-3 (+SL) - GA5-4 (-SL) Always Below 1 Ω



viii.

Disconnect the service wire from connector B.


ix.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GA5-3 (+SL) - GA5-4 (-SL) Always 1 MΩ or higher
GA5-3 (+SL) - Body ground Always 1 MΩ or higher
GA5-4 (-SL) - Body ground Always 1 MΩ or higher




b.

w/ Side Airbag

i.

Disconnect the instrument panel wire connector from the engine room main wire.

C384701C01
2.646,0.49 3.01,0.677 0.365,0.188 4.74,0.521 5.104,0.708 0.365,0.188 3.031,1.385 3.5,1.219 true 5.146,1.26 5.604,0.958 true 6.49,1.281 5.792,0.969 true 4.135,1.365 3.667,1.229 true 5.531,1.542 5.698,1.323 false 0.135,1.125 0.448,1.281 0.313,0.156 10 false *1 1.594,1.198 1.906,1.354 0.313,0.156 10 false *2 0.771,0.531 1.083,0.688 0.313,0.156 10 false *3 1.208,0.531 1.521,0.688 0.313,0.156 10 false *4 4.156,0.448 4.469,0.604 0.313,0.156 10 false *5 6.625,0.479 6.938,0.635 0.313,0.156 10 false *6 5.375,1.542 5.688,1.698 0.313,0.156 10 false *7 0.396,0.729 0.552,0.906 0.156,0.177 10 false F 3.479,0.135 3.792,0.292 0.313,0.156 10 false *a 5.854,0.115 6.167,0.271 0.313,0.156 10 false *b 0.698,0.948 0.854,1.125 0.156,0.177 10 false E 0.958,0.948 1.115,1.125 0.156,0.177 10 false D 1.115,0.948 1.271,1.125 0.156,0.177 10 false C 1.375,0.948 1.531,1.125 0.156,0.177 10 false B 1.677,0.698 1.833,0.875 0.156,0.177 10 false A 2.688,0.5 3.146,0.698 0.458,0.198 10 false GA5 4.813,0.542 5.271,0.74 0.458,0.198 10 false G1 2.75,1.313 3.208,1.51 0.458,0.198 10 false +SL 4.104,1.323 4.563,1.521 0.458,0.198 10 false -SL 5.01,1.292 5.469,1.49 0.458,0.198 10 false +SL 6.438,1.302 6.896,1.5 0.458,0.198 10 false -SL
*1 Front Airbag Sensor LH *2 Center Airbag Sensor
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



ii.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GA5-3 (+SL) - Body ground Ignition switch ON Below 1 V
GA5-4 (-SL) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


vi.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



vii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GA5-3 (+SL) - GA5-4 (-SL) Always Below 1 Ω



viii.

Disconnect the service wire from connector B.


ix.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GA5-3 (+SL) - GA5-4 (-SL) Always 1 MΩ or higher
GA5-3 (+SL) - Body ground Always 1 MΩ or higher
GA5-4 (-SL) - Body ground Always 1 MΩ or higher





OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE