The rear airbag sensor consists of the safing sensor, diagnostic circuit, lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630, B1632, B1635 or B1637 is stored when a malfunction is detected in the rear airbag sensor circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1630 | Either condition is met:
·
A rear airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Rear airbag sensor RH ·
Center airbag sensor |
| B1632 | Either condition is met:
·
A rear airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Rear airbag sensor RH ·
Center airbag sensor |
| B1635 | Either condition is met:
·
A rear airbag sensor LH malfunction. ·
A center airbag sensor malfunction. |
·
Rear airbag sensor LH ·
Center airbag sensor |
| B1637 | Either condition is met:
·
A rear airbag sensor LH malfunction. ·
A center airbag sensor malfunction. |
·
Rear airbag sensor LH ·
Center airbag sensor |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).
After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).
Turn the ignition switch to ON.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1630, B1632, B1635 and B1637 are not output | A |
| DTC B1635 or B1637 is output | B |
| DTC B1630 or B1632 is output | C |
Codes other than DTC B1630,B1632,B1635 and B1637 may be output at this time, but they are not related to this check.
C
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1630, B1632, B1635 and B1637 are not output | A |
| DTC B1635 or B1637 is output (for 3 door) | B |
| DTC B1635 or B1637 is output (for 5 door) | C |
| DTC B1630 or B1632 is output | D |
Codes other than DTC B1630,B1632,B1635 and B1637 may be output at this time, but they are not related to this check.
| *1 | Rear Airbag Sensor LH |
| *2 | Center Airbag Sensor |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
D
A
B
C
| *1 | Rear Airbag Sensor RH |
| *2 | Center Airbag Sensor |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1630, B1632, B1635 and B1637 are not output | A |
| DTC B1630 or B1632 is output (for 3 Door) | B |
| DTC B1630 or B1632 is output (for 5 Door) | C |
| DTC B1635 or B1637 is output | D |
Codes other than B1630,B1632,B1635 and B1637 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
D
A
B
C