Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1676  Lost Communication with Rear Floor Airbag Sensor RH  B1677  Rear Floor Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

HINT:

"Rear floor side airbag sensor RH" refers to the rear floor side airbag sensor.


The rear floor side airbag sensor circuit consists of the center airbag sensor and rear floor side airbag sensor.

The rear floor side airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1676 or B1677 is stored when a malfunction is detected in the rear floor side airbag sensor circuit

DTC Code DTC Detection Condition Trouble Area
B1676 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the rear floor side airbag sensor circuit for 2 seconds.

·

A rear floor side airbag sensor malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear floor side airbag sensor

·

Center airbag sensor


B1677 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the rear floor side airbag sensor circuit for 2 seconds.

·

A rear floor side airbag sensor malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear floor side airbag sensor

·

Center airbag sensor



WIRING DIAGRAM

C216829E15
1.188,1.26 1.604,1.417 0.417,0.156 10 false BER+ 1.208,2.604 1.625,2.76 0.417,0.156 10 false BER- 5.677,1.344 6.115,1.563 0.438,0.219 10 false BDR+ 5.677,2.667 6.135,2.875 0.458,0.208 10 false BDR- 1.677,1.177 1.833,1.323 0.156,0.146 10 false 2 1.688,2.51 1.844,2.677 0.156,0.167 10 false 1 5.396,1.188 5.615,1.344 0.219,0.156 10 false 21 5.385,2.531 5.625,2.688 0.24,0.156 10 false 22 0.271,3.708 0.594,3.896 0.323,0.188 10 false Q5 0.271,3.885 2.229,4.125 1.958,0.24 10 false Rear Floor Side Airbag Sensor 5.448,3.719 5.885,3.906 0.438,0.188 10 false Q43 5.448,3.875 6.875,4.042 1.427,0.167 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and rear floor side airbag sensor.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and rear floor side airbag sensor.


b.
C208245E01
0.329,1.707 0.522,1.875 0.193,0.167 10 *1 2.111,1.707 2.304,1.875 0.193,0.167 10 *2

Check that the connectors (on the center airbag sensor side and rear floor side airbag sensor side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Rear Floor Side Airbag Sensor
*2 Center Airbag Sensor



OK

3.CHECK REAR FLOOR SIDE AIRBAG SENSOR CIRCUIT

NG

REPLACE FLOOR WIRE

3.CHECK REAR FLOOR SIDE AIRBAG SENSOR CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C384702C02
2.49,0.344 2.771,0.563 0.281,0.219 4.896,0.323 5.25,0.542 0.354,0.219 1.021,0.958 1.021,0.479 1.021,0.479 1.146,0.479 false 2.917,1.313 3.333,0.896 true 4.063,1.24 3.573,0.906 true 5.188,1.281 5.719,1.031 true 6.51,1.313 5.823,1.042 true 5.563,1.573 5.76,1.448 true 0.333,1.292 0.646,1.448 0.313,0.156 10 false *1 1.708,1.156 2.021,1.313 0.313,0.156 10 false *2 1.188,0.406 1.5,0.563 0.313,0.156 10 false *3 4.073,0.385 4.385,0.542 0.313,0.156 10 false *4 6.615,0.344 6.927,0.5 0.313,0.156 10 false *5 5.479,1.594 5.792,1.75 0.313,0.156 10 false *6 0.427,0.927 0.583,1.125 0.156,0.198 10 false D 0.771,1.125 0.927,1.323 0.156,0.198 10 false C 2.76,1.313 3.167,1.5 0.406,0.188 10 false BER- 1.604,0.938 1.76,1.135 0.156,0.198 10 false A 3.927,1.281 4.333,1.469 0.406,0.188 10 false BER+ 6.438,1.344 6.844,1.531 0.406,0.188 10 false BDR+ 5.01,1.313 5.417,1.5 0.406,0.188 10 false BDR- 2.542,0.375 2.854,0.531 0.313,0.156 10 false Q5 4.969,0.354 5.281,0.51 0.313,0.156 10 false Q43 1.323,1.125 1.479,1.323 0.156,0.198 10 false B 3.354,0.125 3.667,0.281 0.313,0.156 10 false *a 5.771,0.135 6.083,0.292 0.313,0.156 10 false *b

Text in Illustration
*1 Rear Floor Side Airbag Sensor *2 Center Airbag Sensor
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Rear Floor Side Airbag Sensor)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q5-2 (BER+) - Body ground Ignition switch ON Below 1 V
Q5-1 (BER-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 21 (BDR+) and 22 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q5-2 (BER+) - Q5-1 (BER-) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q5-2 (BER+) - Q5-1 (BER-) Always 1 MΩ or higher
Q5-2 (BER+) - Body ground Always 1 MΩ or higher
Q5-1 (BER-) - Body ground Always 1 MΩ or higher




OK

4.CHECK REAR FLOOR SIDE AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

4.CHECK REAR FLOOR SIDE AIRBAG SENSOR
a.
C171812E03
0.666,1.37 0.817,1.539 0.151,0.170 10 *1 1.801,1.37 1.993,1.539 0.192,0.170 10 *2

Connect the connectors to the center airbag sensor.


b.

Temporarily replace the rear floor side airbag sensor with a new one.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1676 and B1677 are not output.


HINT:

Codes other than DTC B1676 and B1677 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Rear Floor Side Airbag Sensor
*2 Center Airbag Sensor



OK

NG