Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1692  Lost Communication with Side Airbag Sensor RH  B1697  Lost Communication with Side Airbag Sensor LH  


DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, rear airbag sensor LH or RH and side airbag sensor LH or RH.

The rear airbag sensor LH or RH and side airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1692 or B1697 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH).

DTC Code DTC Detection Condition Trouble Area
B1692 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) for 2 seconds.

·

A side airbag sensor RH malfunction.

·

A rear airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front door wire RH

·

Side airbag sensor RH

·

Rear airbag sensor RH

·

Center airbag sensor


B1697 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag LH and curtain shield airbag LH) for 2 seconds.

·

A side airbag sensor LH malfunction.

·

A rear airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front door wire LH

·

Side airbag sensor LH

·

Rear airbag sensor LH

·

Center airbag sensor



WIRING DIAGRAM

C175145E49
1.188,0.99 1.615,1.156 0.427,0.167 10 false BBR+ 0.083,0.031 1.094,0.198 1.01,0.167 12 false for RH Side: 1.698,0.896 1.865,1.063 0.167,0.167 10 false 4 5.417,0.896 5.625,1.115 0.208,0.219 10 false 17 5.417,1.708 5.625,1.875 0.208,0.167 10 false 18 1.698,1.698 1.865,1.865 0.167,0.167 10 false 3 1.698,3.083 1.865,3.25 0.167,0.167 10 false 1 3.656,3.083 3.823,3.25 0.167,0.167 10 false 2 1.698,3.865 1.865,4.031 0.167,0.167 10 false 2 3.667,3.865 3.833,4.031 0.167,0.167 10 false 1 2.698,2.948 2.865,3.115 0.167,0.167 10 false 1 2.698,3.729 2.865,3.896 0.167,0.167 10 false 2 1.188,1.792 1.615,1.958 0.427,0.167 10 false BBR- 5.688,0.99 6.115,1.156 0.427,0.167 10 false BBR+ 5.688,1.792 6.115,1.958 0.427,0.167 10 false BBR- 1.188,3.198 1.615,3.365 0.427,0.167 10 false BCR+ 0.531,4.677 0.781,4.844 0.25,0.167 10 false Q4 0.531,4.854 2.063,5.021 1.531,0.167 10 false Rear Airbag Sensor RH 3.625,4.677 3.938,4.844 0.313,0.167 10 false J8 3.604,4.854 5.406,5.021 1.802,0.167 10 false Side Airbag Sensor RH 5.635,4.677 5.948,4.844 0.313,0.167 10 false Q43 5.625,4.854 7.021,5.021 1.396,0.167 10 false Center Airbag Sensor 3.885,3.198 4.313,3.365 0.427,0.167 10 false BCR+ 2.604,3.198 2.896,3.365 0.292,0.167 10 false JQ1 2.604,3.969 2.896,4.135 0.292,0.167 10 false JQ1 1.188,3.969 1.615,4.135 0.427,0.167 10 false BCR- 3.896,3.969 4.323,4.135 0.427,0.167 10 false BCR-

C175145E50
1.188,0.99 1.615,1.156 0.427,0.167 10 false BBL+ 0.083,0.031 1.094,0.198 1.01,0.167 12 false for LH Side: 1.698,0.896 1.865,1.063 0.167,0.167 10 false 4 5.427,0.896 5.615,1.083 0.188,0.188 10 false 24 5.417,1.708 5.625,1.875 0.208,0.167 10 false 23 1.698,1.698 1.865,1.865 0.167,0.167 10 false 3 1.698,3.083 1.865,3.25 0.167,0.167 10 false 1 3.656,3.083 3.823,3.25 0.167,0.167 10 false 2 1.698,3.865 1.865,4.031 0.167,0.167 10 false 2 3.667,3.865 3.833,4.031 0.167,0.167 10 false 1 2.698,2.948 2.865,3.115 0.167,0.167 10 false 2 2.698,3.729 2.865,3.896 0.167,0.167 10 false 1 1.188,1.792 1.615,1.958 0.427,0.167 10 false BBL- 5.688,0.99 6.115,1.156 0.427,0.167 10 false BBL+ 5.688,1.792 6.115,1.958 0.427,0.167 10 false BBL- 1.188,3.198 1.615,3.365 0.427,0.167 10 false BCL+ 0.531,4.677 0.781,4.844 0.25,0.167 10 false R4 0.531,4.854 2.063,5.021 1.531,0.167 10 false Rear Airbag Sensor LH 3.615,4.677 3.927,4.844 0.313,0.167 10 false K8 3.594,4.854 5.385,5.021 1.792,0.167 10 false Side Airbag Sensor LH 5.646,4.677 5.958,4.844 0.313,0.167 10 false R49 5.635,4.854 7.031,5.021 1.396,0.167 10 false Center Airbag Sensor 3.885,3.198 4.313,3.365 0.427,0.167 10 false BCL+ 2.594,3.177 2.927,3.344 0.333,0.167 10 false KR1 2.594,3.958 2.927,4.125 0.333,0.167 10 false KR1 1.188,3.969 1.615,4.135 0.427,0.167 10 false BCL- 3.896,3.969 4.323,4.135 0.427,0.167 10 false BCL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692 and B1697 are not output A
DTC B1697 is output B
DTC B1692 is output C

HINT:

Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.




C

2.CHECK CONNECTION OF CONNECTORS

A

B

8.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.


b.
C213961E01
0.34,2.885 0.532,3.053 0.193,0.167 10 *1 1.234,0.206 1.427,0.373 0.193,0.167 10 *2 2.09,2.751 2.283,2.918 0.193,0.167 10 *3

Check that the connectors (on the center airbag sensor side, rear airbag sensor RH side and side airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH
*3 Center Airbag Sensor



OK

4.CHECK REAR AIRBAG SENSOR RH

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK REAR AIRBAG SENSOR RH
a.
C171812E03
0.666,1.37 0.817,1.539 0.151,0.170 10 *1 1.801,1.37 1.993,1.539 0.192,0.170 10 *2

Connect the connectors to the center airbag sensor and side airbag sensor RH.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692 and B1697 are not output A
DTC B1697 is output (for 3 Door) B
DTC B1697 is output (for 5 Door) C
DTC B1692 is output D

HINT:

Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Center Airbag Sensor


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



D

5.CHECK SIDE AIRBAG SENSOR RH CIRCUIT

A

B

C

5.CHECK SIDE AIRBAG SENSOR RH CIRCUIT
a.

Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

C384675C08
2.583,0.573 2.896,0.781 0.313,0.208 4.688,0.427 5,0.635 0.313,0.208 6.115,1.281 5.698,0.854 true 3.167,1.281 3.698,0.958 true 4.333,1.271 3.823,0.948 true 5.198,1.281 5.615,0.865 true 4.083,1.615 3.76,1.615 3.76,1.615 3.76,1.365 false 0.406,1.24 0.719,1.396 0.313,0.156 10 false *1 1.833,1.229 2.146,1.385 0.313,0.156 10 false *2 4.375,0.573 4.688,0.729 0.313,0.156 10 false *3 6.635,0.594 6.948,0.75 0.313,0.156 10 false *4 4.135,1.531 4.448,1.688 0.313,0.156 10 false *5 4.219,1.292 4.833,1.49 0.615,0.198 10 false BCR+ 3,1.302 3.625,1.5 0.625,0.198 10 false BCR- 2.635,0.594 2.948,0.792 0.313,0.198 10 false J8 4.771,0.448 5.083,0.646 0.313,0.198 10 false Q4 0.51,0.76 0.667,0.958 0.156,0.198 10 false F 0.938,1.021 1.094,1.219 0.156,0.198 10 false E 1.396,1.021 1.552,1.219 0.156,0.198 10 false B 1.094,1.021 1.25,1.219 0.156,0.198 10 false D 1.229,1.021 1.385,1.219 0.156,0.198 10 false C 1.75,0.792 1.906,0.99 0.156,0.198 10 false A 3.625,0.167 3.938,0.323 0.313,0.156 10 false *a 5.708,0.177 6.021,0.333 0.313,0.156 10 false *b 5.021,1.302 5.635,1.5 0.615,0.198 10 false BCR+ 6.021,1.313 6.646,1.51 0.625,0.198 10 false BCR-
*1 Side Airbag Sensor RH *2 Rear Airbag Sensor RH
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q4-1 (BCR+) - Body ground Ignition switch ON Below 1 V
Q4-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-1 (BCR+) - Q4-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-1 (BCR+) - Q4-2 (BCR-) Always 1 MΩ or higher
Q4-1 (BCR+) - Body ground Always 1 MΩ or higher
Q4-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

6.CHECK SIDE AIRBAG SENSOR RH

NG

7.CHECK FLOOR WIRE (REAR AIRBAG SENSOR RH - FRONT DOOR WIRE RH)
6.CHECK SIDE AIRBAG SENSOR RH
a.
C171828E15
0.469,1.49 0.635,1.649 0.165,0.158 10 *1 2.141,1.49 2.304,1.656 0.163,0.165 10 *2

Connect the connector to the rear airbag sensor RH.


b.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692 and B1697 are not output A
DTC B1697 is output B
DTC B1692 is output C

HINT:

Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Airbag Sensor LH
*2 Rear Airbag Sensor RH


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

7.CHECK FLOOR WIRE (REAR AIRBAG SENSOR RH - FRONT DOOR WIRE RH)
a.

Disconnect the floor wire connector from the front door wire RH.

C384676C10
2.74,0.396 3.115,0.594 0.375,0.198 4.854,0.406 5.229,0.604 0.375,0.198 6.552,1.26 5.958,0.865 true 3.646,1.542 3.646,1.677 3.646,1.677 4.438,1.677 true 3.021,0.958 3.552,0.698 true 4.333,1 3.781,0.719 true 5.281,1.229 5.833,0.875 true 0.344,1.167 0.656,1.323 0.313,0.156 10 false *1 1.927,1.188 2.24,1.344 0.313,0.156 10 false *2 0.927,0.5 1.156,0.667 0.229,0.167 10 false *3 1.354,0.5 1.604,0.677 0.25,0.177 10 false *4 4.323,0.417 4.635,0.573 0.313,0.156 10 false *5 6.688,0.438 7,0.594 0.313,0.156 10 false *6 4.51,1.573 4.823,1.729 0.313,0.156 10 false *7 0.469,0.698 0.625,0.896 0.156,0.198 10 false F 0.813,0.938 0.969,1.135 0.156,0.198 10 false E 1.125,0.938 1.281,1.135 0.156,0.198 10 false D 1.25,0.938 1.406,1.135 0.156,0.198 10 false C 1.563,0.938 1.719,1.135 0.156,0.198 10 false B 1.865,0.708 2.021,0.906 0.156,0.198 10 false A 2.802,0.406 3.146,0.583 0.344,0.177 10 false JQ1 4.948,0.427 5.24,0.604 0.292,0.177 10 false Q4 2.792,0.969 3.406,1.167 0.615,0.198 10 false BCR- 4.229,1.01 4.844,1.208 0.615,0.198 10 false BCR+ 5.083,1.24 5.698,1.438 0.615,0.198 10 false BCR+ 3.563,0.042 3.875,0.198 0.313,0.156 10 false *a 5.938,0.115 6.25,0.271 0.313,0.156 10 false *b 6.469,1.26 7.083,1.458 0.615,0.198 10 false BCR-
*1 Side Airbag Sensor RH *2 Rear Airbag Sensor RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q4-1 (BCR+) - Body ground Ignition switch ON Below 1 V
Q4-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-1 (BCR+) - Q4-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-1 (BCR+) - Q4-2 (BCR-) Always 1 MΩ or higher
Q4-1 (BCR+) - Body ground Always 1 MΩ or higher
Q4-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor LH and side airbag sensor LH.

OK:

The connectors are properly connected.




OK

9.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor, rear airbag sensor LH and side airbag sensor LH.


b.
E272022C08
0.323,2.698 0.635,2.854 0.313,0.156 10 false *1 1.229,0.323 1.542,0.479 0.313,0.156 10 false *2 2.146,3.063 2.458,3.219 0.313,0.156 10 false *3
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH
*3 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side, rear airbag sensor LH side and side airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

10.CHECK REAR AIRBAG SENSOR LH

NG

REPLACE HARNESS AND CONNECTOR

10.CHECK REAR AIRBAG SENSOR LH
a.
C385512C01
0.74,1.177 1.052,1.333 0.313,0.156 10 false *1 1.781,1.594 2.094,1.75 0.313,0.156 10 false *2
*1 Rear Airbag Sensor RH
*2 Center Airbag Sensor


Connect the connector to the center airbag sensor and side airbag sensor LH.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692 and B1697 are not output A
DTC B1692 is output (for 3 Door) B
DTC B1692 is output (for 5 Door) C
DTC B1697 is output D

HINT:

Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



D

11.CHECK SIDE AIRBAG SENSOR LH CIRCUIT

A

B

C

11.CHECK SIDE AIRBAG SENSOR LH CIRCUIT
a.

Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH.

C384675C09
2.583,0.573 2.896,0.781 0.313,0.208 4.688,0.427 5,0.635 0.313,0.208 6.115,1.281 5.698,0.854 true 3.167,1.281 3.698,0.958 true 4.333,1.271 3.823,0.948 true 5.198,1.281 5.615,0.865 true 4.083,1.615 3.76,1.615 3.76,1.615 3.76,1.365 false 0.406,1.24 0.719,1.396 0.313,0.156 10 false *1 1.833,1.229 2.146,1.385 0.313,0.156 10 false *2 4.281,0.448 4.594,0.604 0.313,0.156 10 false *3 6.583,0.458 6.896,0.615 0.313,0.156 10 false *4 4.135,1.531 4.448,1.688 0.313,0.156 10 false *5 4.333,1.302 4.948,1.5 0.615,0.198 10 false BCL+ 2.948,1.302 3.563,1.5 0.615,0.198 10 false BCL- 4.979,1.302 5.594,1.5 0.615,0.198 10 false BCL+ 6.042,1.302 6.656,1.5 0.615,0.198 10 false BCL- 2.635,0.594 2.948,0.792 0.313,0.198 10 false K8 4.771,0.438 5.083,0.635 0.313,0.198 10 false R4 0.51,0.76 0.667,0.958 0.156,0.198 10 false F 0.938,1.021 1.094,1.219 0.156,0.198 10 false E 1.396,1.021 1.552,1.219 0.156,0.198 10 false B 1.094,1.021 1.25,1.219 0.156,0.198 10 false D 1.229,1.021 1.385,1.219 0.156,0.198 10 false C 1.75,0.792 1.906,0.99 0.156,0.198 10 false A 3.531,0.24 3.844,0.438 0.313,0.198 10 false *a 5.656,0.188 5.969,0.385 0.313,0.198 10 false *b
*1 Side Airbag Sensor LH *2 Rear Airbag Sensor LH
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R4-1 (BCL+) - Body ground Ignition switch ON Below 1 V
R4-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-1 (BCL+) - R4-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-1 (BCL+) - R4-2 (BCL-) Always 1 MΩ or higher
R4-1 (BCL+) - Body ground Always 1 MΩ or higher
R4-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

12.CHECK SIDE AIRBAG SENSOR LH

NG

13.CHECK NO. 2 FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
12.CHECK SIDE AIRBAG SENSOR LH
a.
C171828E15
0.469,1.49 0.635,1.649 0.165,0.158 10 *1 2.141,1.49 2.304,1.656 0.163,0.165 10 *2

Connect the connector to the rear airbag sensor LH.


b.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692 and B1697 are not output A
DTC B1692 is output B
DTC B1697 is output C

HINT:

Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Airbag Sensor RH
*2 Rear Airbag Sensor LH


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

13.CHECK NO. 2 FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
a.

Disconnect the No. 2 floor wire connector from the front door wire LH.

C384676C11
2.74,0.396 3.115,0.594 0.375,0.198 4.854,0.406 5.229,0.604 0.375,0.198 6.552,1.26 5.958,0.865 true 3.646,1.542 3.646,1.677 3.646,1.677 4.438,1.677 true 3.021,0.958 3.552,0.698 true 4.333,1 3.781,0.719 true 5.281,1.229 5.833,0.875 true 0.344,1.167 0.656,1.323 0.313,0.156 10 false *1 1.927,1.188 2.24,1.344 0.313,0.156 10 false *2 0.938,0.531 1.25,0.688 0.313,0.156 10 false *3 1.354,0.531 1.667,0.688 0.313,0.156 10 false *4 4.24,0.438 4.552,0.594 0.313,0.156 10 false *5 6.75,0.427 7.063,0.583 0.313,0.156 10 false *6 4.51,1.573 4.823,1.729 0.313,0.156 10 false *7 0.469,0.698 0.625,0.896 0.156,0.198 10 false F 0.813,0.938 0.969,1.135 0.156,0.198 10 false E 1.125,0.938 1.281,1.135 0.156,0.198 10 false D 1.25,0.938 1.406,1.135 0.156,0.198 10 false C 1.563,0.938 1.719,1.135 0.156,0.198 10 false B 1.865,0.708 2.021,0.906 0.156,0.198 10 false A 2.802,0.427 3.146,0.604 0.344,0.177 10 false KR1 4.948,0.427 5.24,0.604 0.292,0.177 10 false R4 2.792,0.969 3.406,1.167 0.615,0.198 10 false BCL+ 4.229,1.01 4.844,1.208 0.615,0.198 10 false BCL- 6.469,1.292 7.083,1.49 0.615,0.198 10 false BCL- 5.219,1.25 5.833,1.448 0.615,0.198 10 false BCL+ 3.521,0.073 3.833,0.271 0.313,0.198 10 false *a 5.927,0.156 6.24,0.354 0.313,0.198 10 false *b
*1 Side Airbag Sensor LH *2 Rear Airbag Sensor LH
*3 Front Door Wire LH *4 No. 2 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R4-1 (BCL+) - Body ground Ignition switch ON Below 1 V
R4-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-1 (BCL+) - R4-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-1 (BCL+) - R4-2 (BCL-) Always 1 MΩ or higher
R4-1 (BCL+) - Body ground Always 1 MΩ or higher
R4-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE NO. 2 FLOOR WIRE